20-101-1051 Rabbit Semiconductor, 20-101-1051 Datasheet - Page 40
![MODULE RABBITCORE RCM3365](/photos/6/74/67489/20-101-1051_sml.jpg)
20-101-1051
Manufacturer Part Number
20-101-1051
Description
MODULE RABBITCORE RCM3365
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1051.pdf
(164 pages)
Specifications of 20-101-1051
Module/board Type
MPU Core Module
Product
Microcontroller Modules
Core Processor
Rabbit 3000
Flash
512 KBytes
Operating Supply Voltage
3.15 to 3.45 V
Board Size
69 mm x 47 mm x 22 mm
For Use With/related Products
RCM3365
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1111
- Current page: 40 of 164
- Download datasheet (3Mb)
4.2 Serial Communication
The RCM3365/RCM3375 does not have any serial transceivers directly on the board.
However, a serial interface may be incorporated into the board the RCM3365/RCM3375
is mounted on. For example, the Prototyping Board has RS-232 and RS-485 transceiver
chips.
4.2.1 Serial Ports
There are six serial ports designated as Serial Ports A, B, C, D, E, and F. All six serial
ports can operate in an asynchronous mode up to the baud rate of the system clock divided
by 8. An asynchronous port can handle 7 or 8 data bits. A 9th bit address scheme, where
an additional bit is sent to mark the first byte of a message, is also supported.
Serial Port A is normally used as a programming port, but may be used either as an asyn-
chronous or as a clocked serial port once the RCM3365/RCM3375 has been programmed
and is operating in the Run Mode.
Serial Port B is available on the RCM3365/RCM3375, and may be used as an
asynchronous port. PB0 is used to enable Dynamic C to detect whether the xD-Picture
Card is installed. If the card detect is not needed by your application program, you may
remove R96 (see Figure A-5) to disable the xD-Picture Card detect, and then use Serial
Port B as a clocked serial port.
Serial Ports C and D can also be operated in the clocked serial mode. In this mode, a clock
line synchronously clocks the data in or out. Either of the two communicating devices can
supply the clock.
Serial Ports E and F can also be configured as HDLC serial ports. The IrDA protocol is
also supported in SDLC format by these two ports.
4.2.2 Ethernet Port
Figure 8 shows the pinout for the RJ-45 Ethernet port (J2). Note that some Ethernet
connectors are numbered in reverse to the order used here.
Three LEDs are placed next to the RJ-45 Ethernet jack, one to indicate an Ethernet link
(
The RJ-45 connector is shielded to minimize EMI effects to/from the Ethernet signals.
34
LINK
) one to indicate Ethernet activity (
Figure 8. RJ-45 Ethernet Port Pinout
ETHERNET
ACT
), and one to indicate the 10/100Base-T speed.
RabbitCore RCM3365/RCM3375
Related parts for 20-101-1051
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![20-101-0575](/photos/6/75/67539/20-101-0575_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0576](/photos/37/60/376010/bl2500_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0412](/photos/37/60/376043/101-0412_tmb.jpg)
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0411](/photos/37/60/376043/101-0412_tmb.jpg)
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0457](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
![20-101-0455](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
![20-101-0497](/photos/37/60/376011/op6800_rgb_tmb.jpg)
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0456](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
![20-101-0591](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
![20-101-0594](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
![20-101-0602](/photos/37/60/376010/bl2500_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0430](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
![20-101-0462](/photos/37/60/376013/bl2100_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
![20-101-0891](/photos/37/60/376014/bl2600_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0654](/photos/37/60/376011/op6800_rgb_tmb.jpg)
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: