IDT92HD75B2X5NLGXYAX8 IDT, Integrated Device Technology Inc, IDT92HD75B2X5NLGXYAX8 Datasheet - Page 32

• Manufacturer Part Number: IDT92HD75B2X5NLGXYAX8
• Description: IC AUDIO CODEC HD 4CH 32-VFQFPN
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Audio Codec, HDr

Specifications of IDT92HD75B2X5NLGXYAX8

• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: No
• S/n Ratio, Adcs / Dacs (db) Typ: 86 / 95
• Dynamic Range, Adcs / Dacs (db) Typ: 86 / 93
• Voltage - Supply, Analog: 3.14 V ~ 3.47 V; 3.8 V ~ 4.2 V; 4.28 V ~ 4.73 V; 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.14 V ~ 3.47 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 32-VFQFN, 32-VFQFPN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 92HD75B2X5NLGXYAX8

4-CHANNEL HD AUDIO CODECS OPTIMIZED FOR LOW POWER
Phased Locked Loop
ESD / Latchup
92HD75B
4-CHANNEL HD AUDIO CODECS OPTIMIZED FOR LOW POWER
VREFOut Drive
VREFILT (VAG)
PLL lock time
PLL (or Azalia Bit CLK) 24MHz clock jitter
Latch-up
ESD - Human Body Model
Charged Device Model
1.Dynamic Range is the ratio of the full scale signal to the noise output with a -60dBFS signal as defined in AES17 as SNR in the
presence of signal and outlined in AES6id, measured “A weighted” over 20 Hz to 20 kHz bandwidth.
2.Ratio of Full Scale signal to idle channel noise output is measured “A weighted” over a 20 Hz to a 20 kHz bandwidth.
(AES17-1991 Idle Channel Noise or EIAJ CP-307 Signal-to-noise Ratio).
3.THD+N ratio as defined in AES17 and outlined in AES6id,non-weighted, over 20 Hz to 20 kHz bandwidth.Results at the jack
are dependent on external components and will likely be 1 - 2dB worse.
4.Peak-to-Peak Ripple over Passband meets ± 0.125dB limits, 48 kHz or 44.1 kHz Sample Frequency. 1dB limit.
5.Stop Band rejection determines filter requirements. Out-of-Band rejection determines audible noise.
6.The integrated Out-of-Band noise generated by the DAC process, during normal PCM audio playback, over a bandwidth 28.8
to 100 kHz, with respect to a 1 Vrms DAC output.
7.In series with 5Ω. Maximum output capacitance is reduced to 220pF if a single pole 30kHz filter is added to attenuate conversion
noise.
8.Gain drift is the change in analog volume control gain for each step across the supported 0
referenced to the 25
9.± 1dB limits for Line Output & 0 dB gain, at -20dBV
10.Spurious tone rejection is tested with ADC dither enabled and compared to ADC performance without dither.
11.Everything enabled and active. Does not include 32
12.Idle measurement D3 set for minimum clicks/pops (biases and min. amps. on)
13.All GPIO and Digital microphone pins.
14.VDD is AVDD1 for GPIO5-7 and DVDD_CORE for others.
15.Can be set to 0.5 or 0.8 AVdd.
Parameter
o
C gain value and specified in ppm per
Table 12. 92HD75B 5V, 4.75V, and 3.3V Analog Performance Characteristics
As described in JESD78A Class II
As described in JESD22-A114-B
As described in JESD22-C101
Ω
Conditions
load headphone power.
o
C
32
AVdd
All
All
All
All
All
All
All
92HD75B
o
C TO 70
Min
500
2K
0.45 X
AVdd
o
Typ
150
1.6
1K
96
70
3K
C temperature range
Max
200
500
PC AUDIO
V 1.0 01-09
degC
usec
psec
Unit
mA
V
V
V