IDTSTAC9752AXTAED1XR IDT, Integrated Device Technology Inc, IDTSTAC9752AXTAED1XR Datasheet - Page 29

• Manufacturer Part Number: IDTSTAC9752AXTAED1XR
• Description: IC CODEC AC'97 MIC/JACK 48-QFP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Audio Codec '97r

Specifications of IDTSTAC9752AXTAED1XR

• Resolution (bits): 20 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: Yes
• S/n Ratio, Adcs / Dacs (db) Typ: 85 / 92
• Voltage - Supply, Analog: 3.14 V ~ 3.47 V; 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.14 V ~ 3.47 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-QFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: STAC9752AXTAED1XR

IDT™
AC’97 2.3 CODECS WITH STEREO MICROPHONE & UNIVERSAL JACK
STAC9752A/9753A
AC’97 2.3 CODECS WITH STEREO MICROPHONE & UNIVERSAL JACK
4.6.2.
BIT_CLK and SDATA_IN are transitioned low immediately following decode of the write to the Pow-
erdown Register (26h) with PR4. When the AC‘97 Controller driver is at the point where it is ready to
program the AC-Link into its low power mode, slots 1 and 2 are assumed to be the only valid stream
in the audio output frame.
After programming the AC‘97 device to this low power, halted mode, the AC‘97 Controller is required
to drive and keep SYNC and SDATA_OUT low.
Once the AC‘97 CODEC has been instructed to halt BIT_CLK, a special “wake-up” protocol must be
used to bring the AC-Link to the active mode since normal audio output and input frames can not be
communicated in the absence of BIT_CLK.
Waking up the AC-Link
There are two methods for bringing the AC-Link out of a low power, halted mode. Regardless of the
method, it is the AC‘97 Controller that performs the wake-up task.
4.6.2.1.
AC-Link protocol provides for a “Cold AC‘97 Reset”, and a “Warm AC‘97 Reset”. The current power-
down state would ultimately dictate which form of AC‘97 reset is appropriate. Unless a “cold” or “reg-
ister” reset (a write to the Reset Register) is performed, wherein the AC‘97 registers are initialized to
their default values, registers are required to keep state during all powerdown modes.
Once powered down, re-activation of the AC-Link via re-assertion of the SYNC signal must not occur
for a minimum of four audio frame times following the frame in which the powerdown was triggered.
When AC-Link powers up the CODEC indicates readiness via the CODEC Ready bit (input slot 0, bit
15).
4.6.2.2.
The STAC9752A/9753A (running off Vaux) can trigger a wake event (PME#) by transitioning
SDATA_IN from low to high and holding it high until either a warm or cold reset is observed on the
S D A T A _ O U T
S D A T A _ I N
B I T _ C L K
N o t e : B I T _ C L K n o t t o s c a l e
S Y N C
Controller Initiates Wake-up
CODEC Initiates Wake-up
Figure 13. STAC9752A/9753A Powerdown Timing
s l o t 2
f r a m e
s l o t 2
f r a m e
p e r
p e r
29
T A G
T A G
W r i t e t o
0 x 2 0
DATA
P R 4
STAC9752A/9753A
PC AUDIO
V 1.5 1206