IDTSTAC9205X5TAEB2XR IDT, Integrated Device Technology Inc, IDTSTAC9205X5TAEB2XR Datasheet - Page 22

• Manufacturer Part Number: IDTSTAC9205X5TAEB2XR
• Description: IC AUDIO CODEC 4CH HD 5V 48-LQFP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Audio Codec, HDr

Specifications of IDTSTAC9205X5TAEB2XR

• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: No
• S/n Ratio, Adcs / Dacs (db) Typ: 98 / 103
• Dynamic Range, Adcs / Dacs (db) Typ: 98 / 95
• Voltage - Supply, Analog: 3.14 V ~ 3.47 V; 3.8 V ~ 4.2 V; 4.28 V ~ 4.73 V; 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.14 V ~ 3.47 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: STAC9205X5TAEB2XR

IDT™
4-CHANNEL HD AUDIO CODEC WITH QUAD DIGITAL MICROPHONE INTERFACE
STAC9204/9205
4-CHANNEL HD AUDIO CODEC WITH QUAD DIGITAL MICROPHONE INTERFACE
1.3.9.
1.3.10. Analog PC-Beep
1.3.11.
Power Management
Table 5 describes the active functionality in each power state.
The D3-default state is available for HD Audio compliance. The programmable values exposed via
vendor-specific settings are under the IDT Device Driver control for further power reduction.
The default power state for the Audio Function Group after reset is D3-default.
PC Beep may need to be active on power up, in which case the BIOS is responsible for enabling it
by setting AnalogBeepEn in the AFG AnaCtrl widget. The PC_BEEP input is routed directly to the
MONO_OUT, LINE_OUT and HP_OUT pins of the CODEC. Because the PC_BEEP input drive is
often a full scale digital signal, some resistive attenuation of the PC_BEEP input is recommended to
keep the beep tone within reasonable volume levels. The user should mute this input before using
any other mixer input because the PC Beep input can contribute noise to the lineout during normal
operation.
Analog PC-Beep is not supported during Link Reset.
Headphone Drivers
Performance degradation will occur when using two headphones simultaneously. See the electrical
specifications for details.
Headphone (HP) Amps
1. VAG is kept active when amplifiers are turned off.
2. If BITCLK is not active, a wake event must be generated. Otherwise an unsolicited response
3. Not active if BITCLK is not running.
4. This mode can only be exited with a Bus Reset.
5. VAG is always ramped up and down gradually, except in the case of a sudden power
Differential Amplifiers
is sent.
removal.
Port Sense
Function
VrefOut
AZ-Link
Ports
DAC
ADC
VAG
Table 5. Power Management
D0-D1
On
On
On
On
On
On
On
On
On
22
Off
Off
On
On
On
On
On
On
On
D2
D3-default
STAC9204/9205
Off
On
On
On
Off
Off
Off
Off
Off
1
2
3
5
Programmable
Programmable
Programmable
D3-alternate
Off
Off
Off
Off
Off
Off
PC AUDIO
V 1.0 12/06
4