Z87L0116ASC1937 Zilog, Z87L0116ASC1937 Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/7/729/zilog_sml.jpg)
Z87L0116ASC1937
Manufacturer Part Number
Z87L0116ASC1937
Description
IC FHSS PHONE CTRL 144-VQFP
Manufacturer
Zilog
Datasheet
1.Z87L0116ASC.pdf
(51 pages)
Specifications of Z87L0116ASC1937
Controller Type
Phone Controller
Interface
Bus
Voltage - Supply
3 V ~ 3.6 V
Current - Supply
55mA
Operating Temperature
-20°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
144-QFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Z87001/Z87L01
ROMless Spread Spectrum Cordless Phone Controller
The following table summarizes the fields allowing control
of frame synchronization and basic frame timing.
SYNC_SEARCH-MODE
SYNC_SEARCH_WORD
UW_LOCATION
WINDOW_SIZE
MULTIPLEX_SWITCH
SYNC_ACQ_IND
SYNC_ACQ_CLEAR
FRAME_COUNTER
FS_INT_ENABLE
FRAME_START_IND
FRAME_START_CLEAR
SYNC_SEARCH-MODE
RF Interface
Several control fields are available in the Z87001 register
set to control the timing and polarity of the RF module in-
terface signals.
A first field, RFEON_POLARITY, controls the polarity of
the RFEON pin. This pin should be used to control the
power of the RF module. It is asserted by the Z87001 when
the RF module is in use, and de-asserted in sleep mode.
The sleep mode is used by the handset to save battery life
when no phone call is in process (See “Sleep mode”, be-
low).
The SYLE pin (Synthesizer Load Enable), which carries a
“load enable” pulse that tells an external RF synthesizer to
generate the next RF channel, is controlled by two fields.
The HOP_ENABLE field is a global enable signal for the
SYLE signals. The SYLE_POLARITY field defines the po-
larity of the SYLE pin. The system designer should ensure
that the leading edge of the SYLE pulse triggers channel
hopping.
28
Table 3. Frame Synchronizer Control Fields
Field
SSPSTATE
SSPSTATE
RX_CONTROL
CONFIG1
SSPSTATE
SSPSTATUS
SSPSTATE
SSPSTATUS
CONTROL
SSPSTATUS
SSPSTATE
SSPSTATE
Register
Bank
3
3
2
3
3
3
3
3
1
3
3
3
P R E L I M I N A R Y
EXT2
EXT2
EXT1
EXT0
EXT2
EXT3
EXT2
EXT3
EXT6
EXT3
EXT2
EXT2
Ext
In addition to the SYLE signal, the interface to the most RF
synthesizers includes two more input lines, “data” and
“clock”, for serial programming of the data values defining
the RF channel. In order to allow interfacing to various
popular synthesizers, the Z87001 does not have dedicated
clock and data lines with fixed timing. Instead, two general
I/O pins from ports P0 and P1 can be controlled in software
by the DSP core to realize any particular interface timing.
This flexibility is made possible by the high speed, single-
cycle architecture of the DSP core.
The transmitter control includes a global enable signal for
all transmit functions: TX_ENABLE. The transmission start
is controlled by the MOD_PWR_ON field. On the base sta-
tion, the value programmed in MOD_PWR_ON is refer-
enced to the transmit frame counter.
Two
RFTX_PWR_OFF, define the duty cycle of the PAON out-
put pin. On the base station, these fields are referenced to
the transmit frame counter. The RFTX_POLARITY bit de-
fines the polarity of the PAON pin. This pin can be used to
control the transmit section and power amplifier of the ex-
ternal RF module.
On the receive side, two fields define the internal timing of
the receiver. The start of reception is controlled by the
DEMOD_PWR_ON field. Stop of reception (and receiver
power down) is controlled by the DEMOD_PWR_OFF
field. On the base station, these fields are referenced to
the receive frame counter. The RXSW output pin follows
the timing defined by the DEMOD_PWR_ON and OFF
fields.
Two
RFRX_PWR_OFF, define the duty cycle of the TXSW out-
put pin. On the base station, these fields are referenced to
the TRANSMIT (!) frame counter. The RFRX_POLARITY
bit defines the polarity of the TXSW and RXSW pins. The
TXSW pin can be used to control the receive section of the
external RF module.
The various timing control registers reviewed in this para-
graph should be programmed differently for handset and
base station. If the same ROM code is used on base and
handset, the software can determine which station it runs
on by reading the HAND_BASE_SEL bit, which reflects
the state of the HBSW pin.
additional
additional
fields,
fields,
RFRX_PWR_ON
RFTX_PWR_ON
DS96WRL0800
Zilog
and
and