ISP1761ETUM ST-Ericsson Inc, ISP1761ETUM Datasheet - Page 151
ISP1761ETUM
Manufacturer Part Number
ISP1761ETUM
Description
IC USB CTRL HI-SPEED 128TFBGA
Manufacturer
ST-Ericsson Inc
Datasheet
1.ISP1761BEUM.pdf
(164 pages)
Specifications of ISP1761ETUM
Controller Type
USB Peripheral Controller
Interface
Serial
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
128-TFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Other names
ISP1761ET-T
ISP1761ET-T
ISP1761ET-T
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 151 of 164
- Download datasheet (768Kb)
NXP Semiconductors
18. Soldering of through-hole mount packages
ISP1761_5
Product data sheet
18.1 Introduction to soldering through-hole mount packages
18.2 Soldering by dipping or by solder wave
18.3 Manual soldering
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description” .
This text gives a very brief insight into wave, dip and manual soldering.
Wave soldering is the preferred method for mounting of through-hole mount IC packages
on a printed-circuit board.
Driven by legislation and environmental forces the worldwide use of lead-free solder
pastes is increasing. Typical dwell time of the leads in the wave ranges from
3 seconds to 4 seconds at 250 C or 265 C, depending on solder material applied, SnPb
or Pb-free respectively.
The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the plastic
body must not exceed the specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling may be necessary immediately
after soldering to keep the temperature within the permissible limit.
Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is
less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is
between 300 C and 400 C, contact may be up to 5 seconds.
Fig 33. Temperature profiles for large and small components
temperature
MSL: Moisture Sensitivity Level
Rev. 05 — 13 March 2008
= minimum soldering temperature
maximum peak temperature
minimum peak temperature
= MSL limit, damage level
Hi-Speed USB OTG controller
temperature
peak
stg(max)
© NXP B.V. 2008. All rights reserved.
ISP1761
001aac844
). If the
time
150 of 163
Related parts for ISP1761ETUM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC FILTR/CODEC 14BIT AUD 30TSSOP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC FILTR/CODEC 14BIT AUD 30TSSOP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HUB CONTROLLER HS 80-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HOST CONTROLLER 128-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB OTG CONTROLLER 64-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB PERIPH CONTROLLER 64HVQFN
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HOST CTRL FULL-SPD 48HVQF
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 64HVQFN
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 64TFBGA
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 64HVQFN
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL SNGL CHIP 64TFBGA
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HOST/DEVICE CTRLR 64-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 128TFBGA
Manufacturer:
ST-Ericsson Inc
Datasheet: