VQ1101N-51 SMC Corporation, VQ1101N-51 Datasheet - Page 69

• Manufacturer Part Number: VQ1101N-51
• Description: VALVE; SOLENOID; 6 MM; 15 W (MAX.); 24 VDC; 2 POSITION SINGLE; METAL; 0.5 MPA
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of VQ1101N-51

• Brand/series: VQ Series
• Configuration: 2-Position Single
• Enclosure Rating: IP65
• Fluid Type: Air/Inert Gas
• Pressure, Operating: 0.7 MPa
• Primary Type: Solenoid Valve
• Temperature, Ambient: –10° to +50°C
• Valve Type: 5-Port Solenoid, Plug-In, Base Mounted with 2 Position Actuation, Rubber Seal, Negative Common
• Voltage, Coil: 24 VDC

<Ordering example>
Double check block (Separated) for VQ1000
VQ1000-FPG-„„-„
It is used on the outlet side piping to keep the cylinder in
the intermediate position for a long time. Combining the
double check block with a built-in pilot type double check
valve and a 3-position exhaust center solenoid valve will
enable the cylinder to stop in the middle or maintain its
position for long periods of time.
The combination with a 2-position single/double solenoid
valve will permit this block to be used for preventing the
dropping at the cylinder stroke end when the SUP
residual pressure is released.
Dimensions
How to Order
Double check block
VQ1000 FPG
Manifold (DIN rail mounting)
VVQ1000 FPG
When ordering a double check block,
order the DIN rail mounting [-D].
VVQ1000-FPG-06 ... 6-station manifold
IN side port size
Specifications
Single unit
C6M5-D, 3 sets
M5
VQ1000-FPG-
C4M5-D, 3 sets
VQ1000-FPG-
C3
C4
C6
N3
N7
Max. operating pressure
Min. operating pressure
Ambient and fluid temp.
Flow characteristics: C
Max. operating frequency
M5 thread
ø3.2 one-touch fitting
ø4 one-touch fitting
ø6 one-touch fitting
ø5/32" one-touch fitting
ø1/4" one-touch fitting
M3 mounting hole
M2.5 mounting
hole
Residual pressure
release manual
override
Double
check block
2 x C3, C4, C6, M5
C3: ø3.2 one-touch fitting
C4: ø4 one-touch fitting
C6: ø6 one-touch fitting
M5: M5 thread
C4
0.60 dm
06
–5 to 50 C
0.15 MPa
180 c.p.m
Bracket Assembly
0.8 MPa
VQ1000-FPG-FB
M5
2 x C4, C6
C4: ø4 one-touch fitting
C6: ø6 one-touch fitting
3
/(s·bar)
Part no.
Dimensions
OUT side port size
L
L
M5
C3
C4
C6
N3
N7
L1
L2
L3
L1
L2
L3
n
n
163
187.5
198
31
50
60.5
M5 thread
ø3.2 one-touch fitting
ø4 one-touch fitting
ø6 one-touch fitting
ø5/32" one-touch fitting
ø1/4" one-touch fitting
13
01
16
1
Stations
F
174
187.5
198
42
62.5
73
14
2
16 stations
1 station
Tightening torque
0.22 to 0.25 N·m
53
75
85.5
185
200
210.5
15
3
Note) Based on JIS B 8375-1981
64
87.5
98
196
212.5
223
16
4
Formula L1 = 11n + 20
(Supply pressure: 0.5 MPa)
100
110.5
207
225
235.5
17
75
5
Base Mounted
112.5
123
218
237.5
248
18
86
6
• Air leakage from the pipe between the valve and cylinder or from the fittings will prevent the cylinder from
• Since one-touch fittings allow slight air leakage, screw piping (with M5 thread) is recommended when
• Combining double check block with 3-position closed center or pressure center solenoid valve will not work.
• M5 fitting assembly is attached, not incorporated into the double check block. After screwing in the M5
• If the exhaust of the double check block is restricted too much, the cylinder may not operate properly and
• Set the cylinder load so that the cylinder pressure will be within two times that of the supply pressure.
stopping for long periods of time. Check the leakage using neutral household detergent, such as dish
washing soap. Also check the cylinder’s tube gasket, piston packing and rod packing for air leakage.
stopping the cylinder in the middle for long periods of time.
fittings, mount the assembly on the double check block. {Tightening torque: 0.8 to 1.2 N·m}
may not stop intermediately.
125
135.5
229
250
260.5
19
97
Note) When two or more sym-
7
Option
Nil
D
N
Caution
F
Manifold
108
125
135.5
240
250
260.5
20
8
bols are specified, indi-
cate them alphabetically.
Example) -DN
n: Station (Maximum 24)
DIN rail mounting
119
137.5
148
251
262.5
273
21
(For manifold)
With bracket
9
Name plate
None
130
150
160.5
262
275
285.5
10
22
Plug-in Unit
141
162.5
173
273
287.5
298
11
23
Residual pressure release
manual override
D side
152
175
185.5
284
300
310.5
12
24
Stations ···· 1 ··· 2 ··· 3
Drop
prevention
2-position
2n x C3, C4, C6, M5
C3: ø3.2 one-touch fitting
C4: ø4 one-touch fitting
C6: ø6 one-touch fitting
M5: M5 thread
Series
Cylinder side pressure
VVQ1000-FPG-02 1 set
<Example>
(P
VQ1000-FPG-C6M5-D 2 pcs.
<Circuit diagram>
2
)
2n x C4, C6
C4: ø4 one-touch fitting
C6: ø6 one-touch fitting
VQ1000
DIN rail clamp screw
Intermediate
stops
SUP side pressure (P
3-position
exhaust center
U side
1
68
)