LPC1833FET256,551 NXP Semiconductors, LPC1833FET256,551 Datasheet - Page 2

no-image

LPC1833FET256,551

Manufacturer Part Number
LPC1833FET256,551
Description
Microcontrollers (MCU) 32BIT ARM CORTEX-M3 MCU 136KB SRAM
Manufacturer
NXP Semiconductors
Series
LPC18xxr

Specifications of LPC1833FET256,551

Core
ARM Cortex M3
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
150MHz
Connectivity
CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
Peripherals
Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
Number Of I /o
80
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Eeprom Size
-
Ram Size
136K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x10b; D/A 1x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
256-LBGA
Lead Free Status / Rohs Status
 Details
Other names
935293791551
NXP Semiconductors
LPC1850_30_20_10
Objective data sheet
Serial interfaces:
Digital peripherals:
Two PLLs allow CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal. Second PLL can be used for USB.
Clock output.
Quad SPI Flash Interface (SPIFI) with four lanes and data rates of up to 40 MB per
second total.
10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high
throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time
stamping (IEEE 1588-2008 v2).
One High-speed USB 2.0 Host/Device/OTG interface with DMA support and
on-chip PHY.
One High-speed USB 2.0 Host/Device interface with DMA support, on-chip
full-speed PHY and ULPI interface to external high-speed PHY.
Four 550 UARTs with DMA support: one UART with full modem interface; one
UART with IrDA interface; three USARTs support synchronous mode and a smart
card interface conforming to ISO7816 specification.
One C_CAN 2.0B controller with one channel.
Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA
support.
One Fast-mode Plus I
pins conforming to the full I
1 Mbit/s.
One standard I
One I
External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash,
and SDRAM devices.
LCD controller with DMA support and a programmable display resolution of up to
1024H  768V. Supports monochrome and color STN panels and TFT color panels;
supports 1/2/4/8 bpp CLUT and 16/24-bit direct pixel mapping.
SD/MMC card interface.
Eight-channel General-Purpose DMA (GPDMA) controller can access all memories
on the AHB and all DMA-capable AHB slaves.
Up to 80 General-Purpose Input/Output (GPIO) pins with configurable
pull-up/pull-down resistors and open-drain modes.
GPIO registers are located on the AHB for fast access. GPIO ports have DMA
support.
State Configurable Timer (SCT) subsystem on AHB.
Four general-purpose timer/counters with capture and match capabilities.
One motor control PWM for three-phase motor control.
One Quadrature Encoder Interface (QEI).
Repetitive Interrupt timer (RI timer).
Windowed watchdog timer.
Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes
of battery powered backup registers.
Alarm timer; can be battery powered.
2
S interface with DMA support and with one input and one output.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 17 February 2011
2
C-bus interface with monitor mode and standard I/O pins.
2
C-bus interface with monitor mode and with open-drain I/O
2
C-bus specification. Supports data rates of up to
32-bit ARM Cortex-M3 microcontroller
LPC1850/30/20/10
© NXP B.V. 2011. All rights reserved.
2 of 87

Related parts for LPC1833FET256,551