Z16M1720ASG1868 Zilog, Z16M1720ASG1868 Datasheet - Page 277
Z16M1720ASG1868
Manufacturer Part Number
Z16M1720ASG1868
Description
IC PCMCIA INTERFACE 100-VQFP
Manufacturer
Zilog
Datasheet
1.Z0847006PSG.pdf
(330 pages)
Specifications of Z16M1720ASG1868
Applications
*
Interface
*
Voltage - Supply
*
Package / Case
100-LQFP
Mounting Type
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 277 of 330
- Download datasheet (3Mb)
Z80 CPU Peripherals
User Manual
257
“Synchronous Operation” on page 238
section for more details on the
interrupt modes.
After reset, or when the transmitter is not enabled, the Transmit Data output
is held marking. Break may be programmed to generate a spacing line.
With the transmitter fully initialized and enabled, continuous flags are
transmitted on the Transmit Data output.
An abort sequence may be sent by issuing the Send Abort command WR0
CMD1). The Send Abort command causes at least 8, but less than 14, 1s to
be sent before the line reverts to continuous flags. It is possible that the
Abort sequence (eight 1s) could follow up to five continuous 1 bits
(allowed by the zero insertion logic) and thus cause up to thirteen 1s to be
sent. Any data being transmitted and any data in the transmit buffer is lost
when an abort is issued.
When required, an extra 0 is automatically inserted when five contiguous
1s occur in the data stream. Automatic insertion does not apply to flags or
aborts.
Data Transfer and Status Monitoring
SDLC mode allows several combinations of interrupts and Wait/Ready
functions.
Data Transfer Using Interrupts
If the Transmit Interrupt Enable bit is set, an interrupt is generated when the
buffer becomes empty. The interrupt may be satisfied either by writing
another character to the transmitter or by resetting the Transmit Interrupt
Pending latch with a Reset Transmitter Pending command (WR0, CMD5).
If the interrupt is satisfied with this command and no more is written to the
transmitter, then no more transmitter interrupts occur. The result is a
Transmit Underrun condition. When another character is written and sent,
the transmitter can again become empty and interrupt the CPU. Following
the flags in an SDLC operation, the 8-bit address field, control field and
UM008101-0601
Serial Input/Output
Related parts for Z16M1720ASG1868
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PCMCIA Interface Solution
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet: