ZPM3570-E RFM, ZPM3570-E Datasheet - Page 7

• Manufacturer Part Number: ZPM3570-E
• Description: TXRX ZIGBEE PRO MODULE
• Manufacturer: RFM
• Series: ZPMr

Specifications of ZPM3570-E

• Frequency: 2.4GHz ~ 2.5GHz
• Data Rate - Maximum: -
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -103dBm
• Voltage - Supply: 2.4 V ~ 3.4 V
• Current - Receiving: 35mA
• Current - Transmitting: 175mA
• Data Interface: Solder Pad
• Memory Size: 8Mbits
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 583-1162

2.5 Module Pin Out
www.RFM.com
© 2011 by RF Monolithics, Inc.
Pin
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
1
2
3
4
5
6
7
8
9
/SC1MOSI(m)/TXD/PB1/SC1SDA
/SC1MISO(m)/RXD/PB2/SC1SCL
PA5/ADC5/nBOOTMODE
PB6/ADC1/IRQB
PC0/JRST/IRQD
PC2/JTDO/SWO
SC1nSSEL/PB4
SC1SCLK/PB3
SWCLK/JTCK
PC6/OSC32B
PC7/OSC32A
SC1MISO(s)
SC1MOSI(s)
PC4/JTMS
PC1/ADC3
PB5/ADC0
PA4/ADC4
PB0/IRQA
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PC3/JTDI
nRESET
VBATT
Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
PA3
Technical support +1.678.684.2000
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PI
O
O
O
O
O
O
-
I
-
-
-
-
-
-
I
-
-
-
-
-
-
-
E-mail:
Ground
Internal serial flash on/off control (active low),for debugging use only
Programmable I/O control available to the host, or JTAG mode select
Programmable I/O control available to the host, or an interrupt input
Internal serial flash nCS, for debugging use only
Programmable I/O control available to the host, or ADC input, or an
interrupt input
Programmable I/O control available to the host, or an ADC input
JTAG/Serial Wire debugging port clock
Programmable I/O control available to the host, or an interrupt input, or
the JTAG reset input
Ground
Programmable I/O control available to the host, or an ADC input
Ground
Ground
Ground
Ground
Not connected in ZPM3750
Ground
Used internally as the LNA on (active low), for debugging use only
Module reset signal (Internal pull-up)
Ground
Ground
Programmable I/O control available to the host
Ground
Programmable I/O control available to the host, or 32.768 kHz crystal
Programmable I/O control available to the host, or 32.768 kHz crystal
SPI port 1 clock, or programmable I/O control available to the host
Used internally as the serial flash MOSI, for debugging use only
Used internally as the serial flash MISO, for debugging use only
Module power supply
Used internally as the serial flash clock, for debugging use only
Programmable I/O control available to the host, or ADC input
Ground
Programmable I/O control available to the host, or ADC input, or Boot
control, must be left open or pulled high during the reset to enable the
normal firmware boot process.
SPI port 1 MISO (slave)/ MOSI (master) signal, UART TXD signal, I2C
port 1 DATA signal, or programmable I/O control available to the host
SPI port 1 MOSI (slave)/ MISO (master) signal, UART RXD signal, I2C
port 1 CLK signal, or programmable I/O control available to the host.
Programmable I/O control available to the host, or Serial Wire port OUT-
PUT signal, or JTAG data out
SPI port 1 slave select, or programmable I/O control available to the host
Programmable I/O control available to the host, or JTAG data in
Ground
Ground
Ground
[e-mail]
Description
ZPM3570 Data Sheet - 05/25/11
Page 7 of 18