TDA8425 NXP Semiconductors, TDA8425 Datasheet - Page 24
![](/photos/31/40/314084/20pin_sot146-1_sml.jpg)
TDA8425
Manufacturer Part Number
TDA8425
Description
Manufacturer
NXP Semiconductors
Datasheet
1.TDA8425.pdf
(24 pages)
Specifications of TDA8425
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TDA8425
Manufacturer:
PHILIPS
Quantity:
117
Part Number:
TDA8425
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
TDA8425/V7
Manufacturer:
INNOCHIPS
Quantity:
16 562
Part Number:
TDA8425/V7
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Philips Semiconductors
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 C; solder at this temperature must not be in contact
DEFINITIONS
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
PURCHASE OF PHILIPS I
October 1988
Data sheet status
Objective specification
Preliminary specification
Product specification
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Hi-fi stereo audio processor; I
Purchase of Philips I
components in the I
Philips. This specification can be ordered using the code 9398 393 40011.
2
C COMPONENTS
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
2
C system provided the system conforms to the I
2
C components conveys a license under the Philips’ I
2
C-bus
24
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 C, contact may be up to 5 seconds.
2
C specification defined by
2
C patent to use the
Product specification
TDA8425
stg max
). If the