SC16C850IET,157 NXP Semiconductors, SC16C850IET,157 Datasheet - Page 18
![IC UART SINGLE W/FIFO 36-TFBGA](/photos/6/98/69857/36-tfbga_sot912-1_pkg_sml.jpg)
SC16C850IET,157
Manufacturer Part Number
SC16C850IET,157
Description
IC UART SINGLE W/FIFO 36-TFBGA
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C850IBS128.pdf
(55 pages)
Specifications of SC16C850IET,157
Features
Programmable
Number Of Channels
1, UART
Fifo's
128 Byte
Protocol
RS485
Voltage - Supply
2.5 V ~ 3.3 V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
36-TFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935284685157
SC16C850IET
SC16C850IET
SC16C850IET
SC16C850IET
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C850IET,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
SC16C850
Product data sheet
6.11.1 Conditions to enter Sleep mode
6.11.2 Conditions to resume normal operation
6.12 Low power feature
6.11 Sleep mode
Sleep mode is an enhanced feature of the SC16C850 UART. It is enabled when EFR[4],
the enhanced functions bit, is set and when IER[4] bit is set.
Sleep mode is entered when:
In Sleep mode, the UART clock and baud rate clock are stopped. Since most registers are
clocked using these clocks, the power consumption is greatly reduced.
Remark: Writing to the divisor latches, DLL and DLM, to set the baud clock, must not be
done during Sleep mode. Therefore, it is advisable to disable Sleep mode using IER[4]
before writing to DLL or DLM.
SC16C850 resumes normal operation by any of the following:
If the device is awakened by one of the conditions described above, it will return to the
Sleep mode automatically after all the conditions described in
device will stay in Sleep mode until it is disabled by setting any channel’s IER bit 4 to a
logic 0.
When the SC16C850 is in Sleep mode and the host data bus (D[7:0], A[2:0], IOW, IOR,
CS) remains in steady state, either HIGH or LOW, the Sleep mode supply current will be
in the μA range as specified in
toggling or floating then the sleep current will be higher.
A low power feature is provided by the SC16C850 to prevent the switching of the host
data bus from influencing the sleep current. When the pin LOWPWR is activated (logic
HIGH), the device immediately and unconditionally goes into Low power mode. All clocks
are stopped and most host interface pins are isolated to reduce power consumption. The
device only returns to normal mode when the LOWPWR pin is de-asserted. The pin can
be left unconnected because it has an internal pull-down resistor.
•
•
•
•
•
•
•
•
Modem input pins are not toggling.
The serial data input line, RX, is idle for 4 character time (logic HIGH) and AFCR1[4]
is logic 0. When AFCR1[4] is logic 1 the device will go to sleep regardless of the state
of the RX pin (see
The TX FIFO and TX shift register are empty.
There are no interrupts pending.
The RX FIFO is empty.
Receives a start bit on RX pin.
Data is loaded into transmit FIFO.
A change of state on any of the modem input pins
All information provided in this document is subject to legal disclaimers.
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
Rev. 2 — 11 November 2010
Section 7.21
Table 36 “Static
for the description of AFCR1 bit 4).
characteristics”. If any of these signals is
Section 6.11.1
SC16C850
© NXP B.V. 2010. All rights reserved.
are met. The
18 of 55