SC28L198A1A,518 NXP Semiconductors, SC28L198A1A,518 Datasheet - Page 27
![IC UART OCTAL SOT189-3](/photos/6/98/69866/568-84-plcc_sot189-2_sml.jpg)
SC28L198A1A,518
Manufacturer Part Number
SC28L198A1A,518
Description
IC UART OCTAL SOT189-3
Manufacturer
NXP Semiconductors
Type
Octal UART for 3.3 V and 5 V supply voltager
Datasheet
1.SC28L198A1BE557.pdf
(57 pages)
Specifications of SC28L198A1A,518
Number Of Channels
8
Package / Case
84-LCC (J-Lead)
Features
False-start Bit Detection
Fifo's
16 Byte
Voltage - Supply
3.3V, 5V
With Auto Flow Control
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Data Rate
0.4608 MBd
Supply Voltage (max)
5.5 V
Supply Voltage (min)
3 V
Supply Current
150 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Operating Supply Voltage
3.3 V or 5 V
Transmit Fifo
16Byte
Receive Fifo
16Byte
Transmitter And Receiver Fifo Counter
No
Operating Supply Voltage (typ)
3.3/5V
Package Type
PLCC
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
3V
Mounting
Surface Mount
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
935261323518
SC28L198A1A-T
SC28L198A1A-T
SC28L198A1A-T
SC28L198A1A-T
Philips Semiconductors
Table 22. XISR – Xon–Xoff Interrupt Status Register
XISR[7:6] – Received X Character Status. This field can be read to
determine if the receiver has encountered an Xon or Xoff character
in the incoming data stream. These bits are maintained until a read
of the XISR. The field is updated by X character reception
regardless of the state of MR0(7, 3:2) or IMR(4). The field can
therefore be used as a character detector for the bit patterns stored
in the Xon and Xoff Character Registers.
XISR[5:4] – Automatic transmission Status. This field indicates the
last flow control character sent in the Auto Receiver flow control
mode. If Auto Receiver mode has not been enabled, this field will
always read b’00. It will likewise reset to b’00 if MR0(3) is reset. If
the Auto Receiver mode is exited while this field reads b’10, it is the
user’s responsibility to transmit an Xon, when appropriate.
XISR[3:2] – TxD flow Status. This field tracks the transmitter’s flow
status as follows:
XISR[1:0] – TxD character Status. This field allows determination of
the type of character being transmitted. If XISR(1:0) is b’01, the
channel is waiting for a data character to transfer from the TxFIFO.
This condition will only occur for a bit time after an Xon or Xoff
character transmission unless the TxFIFO is empty.
Table 26. BRGTCR – BRG Timer Control Register (BRGTCR)
Start/Stop control and clock select register for the two BRG
counters. The clock selection is for the input to the counters. It is
that clock divided by the number represented by the BRGTU and
BRGTL the will be used as the 16x clock for the receivers and
transmitters. When the BRG timer Clock is selected for the
2006 Aug 10
Bits 7:6
Received X Character Sta-
tus
00 – none
01 – Xoff received
10 – Xon received
11 – both received
Bit 7
BRGTCR b, Register control
0 – Resets the timer register and
holds it stopped
1 – Allows the timer register to
run.
10 – re–enabled. The transmitter had been halted and restarted.
Octal UART for 3.3 V and 5 V supply voltage
00 – normal. The flow control is under host control.
01 – TxD halt pending. After the current character finishes the
transmitter will stop. The status will then change to b’00.
It is sending data characters. After a read of the XISR, it will
return to ”normal” status.
11 – disabled. The transmitter is flow controlled.
Bits 5:4
Automatic X Character transmis-
sion status
00 – none
01 – Xon transmitted
10 – Xoff transmitted
11 – Illegal, does not occur
Bit 6:4
BRGTCR b, Clock selection
000 – Sclk / 16
001 – Sclk / 32
010 – Sclk/ 64
011 – Sclk / 128
100 – X1
101 – X1 / 2
110 – I/O1b
111 – G
IN
(1)
Bits 3:2
TxD flow status
00 – normal
01 – TxD halt pending
10 – re–enabled
11 – flow disabled
27
Bit 3
BRGTCR a, Register control
0 – Resets the timer register and
holds it stopped.
1 – Allows the timer register to
run.
Table 23. WDTRCR – Watch-dog Timer Enable
This register enables the watch-dog Timer for each of the 8
receivers on the Octal UART.
Table 24. BRGTRU
This is the upper byte of the 16 bit value used by the BRG timer in
generating a baud rate clock
Table 25. BRGTRL
This is the lower byte of the 16 bit value used by the BRG timer in
generating a baud rate clock.
receiver(s) or transmitter(s) the receivers and transmitters will
consider it as a 16x clock and further device it by 16. In other words
the receivers and transmitters will always be in the 16x ode of
operation when the internal BRG timer is selected for their clock.
Bit 7
WDT
h
1 on
0 off
Bits 7:0
8 MSB of the BRG Timer divisor.
Bits 7:0
8 LSB of the BRG Timer divisor.
Bit 6
WDT
g
1 on
0 off
Register
Registers, Upper
Registers, Lower
Bit 5
WDT
f
1 on
0 off
–
Bit 4
WDT
e
1 on
0 off
–
Bits 1:0
TxD character status
00 – normal TxD data
01 – wait on normal data
10 – Xoff in pending
11 – Xon in pending
BRG Timer Reload
BRG Timer Reload
Bit 2:0
BRGTCR a, Clock selection
000 – Sclk / 16
001 – Sclk / 32
010 – Sclk / 64
011 – Sclk / 128
100 – X1
101 – X1 / 2
110 – I/O1a
111 – G
Bit 3
WDT
d
1 on
0 off
IN
(0)
Bit 2
WDT
c
1 on
0 off
SC28L198
Product data sheet
Bit 1
WDT
b
1 on
0 off
Bit 0
WDT
a
1 on
0 off