TDA8946AJ/N2,112 NXP Semiconductors, TDA8946AJ/N2,112 Datasheet - Page 5

• Manufacturer Part Number: TDA8946AJ/N2,112
• Description: IC AMP AUDIO PWR 15W STER 17SIL
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA8946AJ/N2,112

• Output Type: 2-Channel (Stereo)
• Package / Case: 17-SIL (Bent and Staggered Leads)
• Max Output Power X Channels @ Load: 15W x 2 @ 8 Ohm
• Voltage - Supply: 4.5 V ~ 18 V
• Features: Depop, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Through Hole
• Product: Class-AB
• Output Power: 15 W
• Available Set Gain: 30 dB
• Thd Plus Noise: 0.07 %
• Operating Supply Voltage: 18 V
• Maximum Power Dissipation: 28000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 8 Ohms
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Type: Single
• Supply Voltage (max): 18 V
• Supply Voltage (min): 4.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-3456-5; 935270283112; TDA8946AJU

Philips Semiconductors
9397 750 09434
Product data
8.2.1 Output power measurement
8.2.2 Headroom
8.2 Power amplifier
The input cut-off frequency is:
For R
As shown in
the switch-on delay during charging of the input capacitors can be minimized. This
results in a good low frequency response and good switch-on behaviour.
Remark: To prevent high frequency oscillations do not leave the inputs open, connect
a capacitor of 4.7 nF across the input pins close to the device (see
The power amplifier is a Bridge-Tied Load (BTL) amplifier with an all-NPN output
stage, capable of delivering a peak output current of 2 A.
The BTL principle offers the following advantages:
The output power as a function of the supply voltage is measured on the output pins
at THD = 10%; see
voltage of 18 V and the maximum available output current: 2 A repetitive peak
current.
Typical CD music requires at least 12 dB (factor 15.85) dynamic headroom -
compared to the average power output - for transferring the loudest parts without
distortion. At V
Average Listening Level (ALL) - music power - without any distortion yields:
The power dissipation can be derived from
respectively 12 dB headroom.
f
f
•
•
•
•
P
i cut off
i cut off
o ALL
Lower peak value of the supply current
The ripple frequency on the supply voltage is twice the signal frequency
No expensive DC-blocking capacitor
Good low frequency performance.
–
i
–
= 32 k and C
=
=
=
-------------
15.85
10 W
Equation
------------------------------------------
2
------------------------------------------------------------------------------
2
CC
0.5
0.5 32 10
= 18
=
Rev. 01 — 01 March 2002
Figure
631
1
i
= 220 nF:
R
2, large capacitors values for the inputs are not necessary; so
V,
i
mW
R
C
10. The maximum output power is limited by the supply
L
1
i
= 8
3
2 x 15 W BTL audio amplifier with DC gain control
220 10
and P
9 –
o
= 10 W at THD = 0.5% (see
Figure 12 on page 11
=
45.2 Hz
© Koninklijke Philips Electronics N.V. 2002. All rights reserved.
TDA8946AJ
for 0 dB
Figure
Figure
15).
8), the
5 of 20
(1)
(2)
(3)