UPB1005GS NEC, UPB1005GS Datasheet
UPB1005GS
Available stocks
Related parts for UPB1005GS
UPB1005GS Summary of contents
Page 1
... PB1005GS-E1 30-pin plastic SSOP (7.62 mm (300)) Remark To order evaluation samples, please contact your local NEC sales office. (Part number for sample order: PB1005GS) The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. ...
Page 2
... PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM IF-MIX in GND (IF-MIX) RF-MIX out V (RF-MIX) CC RF-MIX in GND (RF-MIX) V (1stLO-OSC) CC 1stLO-OSC1 1stLO-OSC2 GND (1stLO-OSC) V (phase detector) CC PD-V 3 out PD-V 2 out PD-V 1 out GND (phase detector ...
Page 3
PRODUCT LINE- + Functions Type Part Number (Frequency unit: MHz) General PC2756T RF down-converter with osc. Tr 2.7 to 3.3 Purpose Wideband PC2756TB Separate IC PC2753GR IF down-converter with gain control amplifier Clock PB1003GS RF/IF ...
Page 4
ABSOLUTE MAXIMUM RATINGS Parameter Symbol Supply Voltage V CC Total Circuit Current I CC Power Dissipation P D Operating Ambient Temperature T A Storage Temperature T stg RECOMMENDED OPERATING RANGE Parameter Symbol Supply Voltage V CC Operating Ambient Temperature T ...
Page 5
ELECTRICAL CHARACTERISTICS (Unless otherwise specified, T Parameter Symbol Total Circuit Current I total CC RF Down-converter Block (f = 1575.42 MHz, f RFin Circuit Current Conversion Gain CG RF RF-SSB Noise Figure NF RF Maximum ...
Page 6
STANDARD CHARACTERISTICS (Unless otherwise specified T Parameter Symbol RF Down-converter Block ( dBm, Z 1stLOin LO Leakage to IF Pin Leakage to RF Pin LO rf Input 3rd Order Intercept IIP RF 3 Point IF ...
Page 7
... Pin should be PD equipped with external RC in order to adjust dumping factor and cutoff frequency. This tuning voltage output must be connected to varactor diode of 15 1st LO-OSC. Ground pin of phase detector + active loop filter. Data Sheet P13860EJ3V0DS00 PB1005GS ...
Page 8
Applied Pin Pin Pin Name Voltage Voltage No. (V) ( 2.7 to 3.3 CC (divider block 2.08 out 18 GND 0 (divider block) 19 REF 1. 2.7 to 3.3 CC (reference block) 21 ...
Page 9
Applied Pin Pin Pin Name Voltage Voltage No. (V) (V) 28 IF-MIX 1.15 out 29 V (IF-MIX 3 (IF-MIX) 2 IF-MIX 2. GND (IF-MIX) 0 Caution Ground pattern on ...
Page 10
TYPICAL CHARACTERISTICS (Unless otherwise specified TOTAL TOTAL CIRCUIT CURRENT vs. SUPPLY VOLTAGE 80 No signals ...
Page 11
IF OUTPUT POWER vs. 1st LO INPUT POWER 1.57542 MHz RFin dBm RFin 1636.8 MHz 1stLOin f = 61.38 MHz 1stIFout 3 ...
Page 12
IF OUTPUT POWER vs. 1st IF INPUT POWER 61.38 MHz 1stIFin 65.472 MHz 2ndLOin dBm 2ndLOin 4.092 MHz 2ndFout ...
Page 13
IF CONVERSION GAIN vs. GAIN CONTROL VOLTAGE 3 2 61.38 MHz 1stIFin dBm 1stIFin f = 65.472 MHz 2ndLOin 20 ...
Page 14
IF OUTPUT POWER vs. 2nd IF INPUT POWER 4.092 MHz 2ndIFin 3 2 ...
Page 15
REFERENCE BLOCK REFERENCE OUTPUT SWING vs. REFERENCE INPUT FREQUENCY 2 1.0V REFin P Reference Input Frequency f ...
Page 16
TEST CIRCUIT Signal Generator 1PIN Spectrum Analyzer Signal Generator V- ...
Page 17
PACKAGE DIMENSIONS 30 PIN PLASTIC SHRINK SOP (300 mil) (UNIT: mm 9.85 0.26 2.0 MAX. 1.7 0.1 0.65 0.3 0.1 0.10 M 0.125 0.075 NOTE Each lead centerline is located within 0. its true position (T.P.) ...
Page 18
... Form a ground pattern as wide as possible to minimize ground impedance (to prevent abnormal oscillation). (3) Keep the track length of the ground pins as short as possible. (4) Connect a bypass capacitor (example: 1 000 pF) to the V (5) Frequency signal input/output pins must be each coupled with capacitor for DC cut. RECOMMENDED SOLDERING CONDITIONS This product should be soldered under the following recommended conditions ...
Page 19
Data Sheet P13860EJ3V0DS00 PB1005GS 19 ...
Page 20
... Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...