UPB586G NEC, UPB586G Datasheet
UPB586G
Related parts for UPB586G
UPB586G Summary of contents
Page 1
... P PB586G/588G or P PB1505GR so that these smaller packages contribute to reduce the mounting space replacing from conventional ICs. The P PB1506GV and P PB1507GV are manufactured using NEC’s high f This process uses silicon nitride passivation film and gold electrodes. These materials can protect chip surface from external pollution and prevent corrosion/migration ...
Page 2
... PIN CONNECTION (Top View PRODUCT LINE-UP Features Part No. (division, Freq.) y512, y256, 2.5 GHz P PB586G y128, y64, 2.5 GHz P PB588G y256, y128, y64 P PB1505GR P PB1506GV 3.0 GHz P PB1507GV This table shows the TYP values of main parameters. Remarks x CHARACTERISTICS. P PB586G and P PB588G are discontinued. ...
Page 3
SYSTEM APPLICATION EXAMPLE 1stIF input from DBS converter BPF To 2150 MHz OSC To 2650 MHz RF unit block of Analog CATV converter To 800 MHz BPF To 2000 MHz PB1506GV PB1507GV ...
Page 4
... CC bypass capacitor (e.g. 10 000 pF) to minimize ground impedance. • OUT 2.6 to 4.7 Divided frequency output pin. This pin is designed as emitter follower output. This pin can be connected to CMOS input due to 1.2 V • • NC Non connection pin. This pin must be openned PB1506GV PB1507GV ...
Page 5
... GHz 1.2 L Connection in the test V CC circuit Connection in the test OPEN or circuit GND Connection in the test V CC circuit Connection in the test OPEN or circuit GND RATINGS UNIT ð0.5 to +6.0 V ð0 0 250 ð40 to +85 qC ð55 to +150 qC NOTICE ...
Page 6
TYPICAL CHARACTERISTICS (Unless otherwise specified T CIRCUIT CURRENT vs. SUPPLY VOLTAGE 25 No signals T = +85° +25° –40° Supply Voltage ...
Page 7
OUTPUT VOLTAGE vs. INPUT RFEQUENCY 2 +85° –10 dBm 1 1.2 1.0 0.8 0.6 0.4 100 1000 f - Input ...
Page 8
OUTPUT VOLTAGE vs. INPUT FREQUENCY 2 +85° –10 dBm in 1.9 1 1.4 1.3 1.2 100 1000 ...
Page 9
OUTPUT VOLTAGE vs. INPUT FREQUENCY 2 +85° –10 dBm in 1 1 1.4 1.3 1.2 100 1000 f - Input ...
Page 10
PB1506GV S vs. OUTPUT FREQUENCY 22 Divide by 64 mode 5 REF 1.0 Units 200.0 mUnits/ 1 171.22 –04.438 hp C MARKER 1 45.0 MHz D START 0.045000000 GHz ...
Page 11
PB1506GV S vs. OUTPUT FREQUENCY 22 Divide by 256 mode 5 REF 1.0 Units 200.0 mUnits/ 1 199.25 –05.992 hp C MARKER 1 45.0 MHz D START 0.045000000 GHz ...
Page 12
PB1507GV S vs. OUTPUT FREQUENCY 22 Divide by 64 mode 5 REF 1.0 Units 200.0 mUnits/ 1 185.13 17.789 hp C MARKER 1 45.0 MHz D 0.045000000 GHz START ...
Page 13
PB1507GV S vs. OUTPUT FREQUENCY 22 Divide by 256 mode 5 REF 1.0 Units 200.0 mUnits/ 1 186.76 17. MARKER 1 45.0 MHz D START 0.045000000 GHz ...
Page 14
... C7 value + stray capacitance on the board and measurement equipment PB1506GV PB1507GV Stray cap OUT SW2 6 C4 OPEN NC 5 Divide ratio setting SW1 Connect Connect to GND or OPEN Monitor 1 M 0.6 pF Oscilloscope or Counter 50 SW2 H L 1/64 1/128 1/128 1/256 CC ...
Page 15
... To measure output voltage swing PB1506GV PB1507GV SW1 SW2 C1 4 OUT GND C5 Monitor 1 M 0.6 pF Stray cap. Oscilloscope or Counter OPEN Divide ratio setting SW2 H L SW1 H 1/64 1/128 L 1/128 1/256 H: Connect Connect to GND or OPEN 15 ...
Page 16
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD PB1506GV SW1 PB1507GV SW1 OUT OUT EVALUATION BOARD CHARACTERS ( thick double-sided copper clad 50 u ...
Page 17
PACKAGE DIMENSIONS 8 PIN PLASTIC SSOP (UNIT: mm) (175 mil 3.0 MAX. 0.65 0.575 MAX PB1506GV PB1507GV detail of lead end 4.94 ±0.2 3.2 ±0.1 0.5 ±0.2 +0.10 ...
Page 18
... Observe precautions for handling because of electro-static sensitive devices. (2) Form a ground pattern as wide as possible to minimize ground impedance (to prevent undesired operation). (3) Keep the wiring length of the ground pins as short as possible. (4) Connect a bypass capacitor (e.g. 10 000 pF) to the V RECOMMENDED SOLDERING CONDITIONS This product should be soldered in the following recommended conditions. ...
Page 19
PB1506GV PB1507GV 19 ...
Page 20
... Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...