ATtiny167 Automotive Atmel Corporation, ATtiny167 Automotive Datasheet - Page 27

• Manufacturer Part Number: ATtiny167 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny167 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

4.2.3
7728G–AVR–06/10
128 KHz Internal Oscillator
Table 4-3.
Notes:
When this Oscillator is selected, start-up times are determined by the SUT Fuses or by CSUT
field as shown in
Table 4-4.
Notes:
The 128 KHz internal Oscillator is a low power Oscillator providing a clock of 128 KHz. The
frequency is nominal at 3V and 25°C. This clock may be selected as the system clock by pro-
gramming CKSEL Fuses or CSEL field as shown in
When this clock source is selected, start-up times are determined by the SUT Fuses or by
CSUT field as shown in
Table 4-5.
Notes:
CSUT1..0
CSUT1..0
SUT1..0
SUT1..0
00
00
10
01
10
11
01
11
(3)
1. If 8 MHz frequency exceeds the specification of the device (depends on Vcc), the CKDIV8
2. The frequency ranges are guideline values.
3. The device is shipped with this CKSEL = “0010”.
4. Flash Fuse bits.
5. CLKSELR register bits.
1. Flash Fuse bits
2. CLKSELR register bits
3. This setting is only available if RSTDISBL fuse is not set
4. The device is shipped with this option selected.
1. Flash Fuse bits
2. CLKSELR register bits
3. This setting is only available if RSTDISBL fuse is not set
(3)
(4)
(1)
(1)
(2)
fuse can be programmed in order to divide the internal frequency by 8.
(2)
Internal Calibrated RC Oscillator Operating Modes
Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
Start-up Times for the 128 kHz Internal Oscillator
Table
Start-up Time from
Power-down/save
Start-up Time from
Frequency Range
Power-down/save
4-4.
Table
6 CK
6 CK
6 CK
6 CK
6 CK
6 CK
7.6 - 8.4
4-5.
(2)
(MHz)
from Reset (Vcc = 5.0V)
Additional Delay from
Additional Delay
14CK + 4.1 ms
Reset (Vcc = 5.0V)
14CK + 65 ms
14CK + 4.1 ms
14CK + 65 ms
Reserved
14CK
Reserved
Table 4-1 on page
14CK
ATtiny87/ATtiny167
(1)
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
25.
CKSEL3..0
CSEL3..0
0010
(3)(4)
(5)
27