ATtiny167 Automotive Atmel Corporation, ATtiny167 Automotive Datasheet - Page 47

• Manufacturer Part Number: ATtiny167 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny167 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

5.9.2
5.9.3
7728G–AVR–06/10
MCUCR – MCU Control Register
PRR – Power Reduction Register
Table 5-2.
• Bit 0 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the
SLEEP instruction is executed. To avoid the MCU entering the sleep mode unless it is the pro-
grammer’s purpose, it is recommended to write the Sleep Enable (SE) bit to one just before
the execution of the SLEEP instruction and to clear it immediately after waking up.
• Bit 6 – BODS: BOD Sleep
The BODS bit must be written to logic one in order to turn off BOD during sleep, see
on page
BODSE in MCUCR. To disable BOD in relevant sleep modes, both BODS and BODSE must
first be set to one. Then, to set the BODS bit, BODS must be set to one and BODSE must be
set to zero within four clock cycles.
The BODS bit is active three clock cycles after it is set. A sleep instruction must be executed
while BODS is active in order to turn off the BOD for the actual sleep mode. The BODS bit is
automatically cleared after three clock cycles.
• Bit 5 – BODSE: BOD Sleep Enable
BODSE enables setting of BODS control bit, as explained in BODS bit description. BOD dis-
able is controlled by a timed sequence.
• Bit 7 - Res: Reserved bit
This bit is reserved in ATtiny87/167 and will always read as zero.
• Bit 6 - Res: Reserved bit
This bit is reserved in ATtiny87/167 and will always read as zero.
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
SM1
0
0
1
1
42. Writing to the BODS bit is controlled by a timed sequence and an enable bit,
Sleep Mode Select
R
7
–
0
R
7
–
0
SM0
0
1
0
1
BODS
R/W
6
0
R
6
–
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Power-save
BODSE
PRLIN
R/W
R/W
5
0
5
0
PRSPI
R/W
PUD
R/W
4
0
4
0
PRTIM1
R/W
3
0
R
3
–
0
ATtiny87/ATtiny167
PRTIM0
R/W
2
0
R
2
–
0
PRUSI
R/W
R
1
–
0
1
0
PRADC
R
0
–
0
R/W
0
0
Table 5-1
MCUCR
PRR
47