SAM9G25 Atmel Corporation, SAM9G25 Datasheet - Page 312

• Manufacturer Part Number: SAM9G25
• Manufacturer: Atmel Corporation

Specifications of SAM9G25

• Flash (kbytes): 0 Kbytes
• Pin Count: 247
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

25.7.2
Name:
Address:
Access:
• SLOT_CYCLE: Maximum Bus Grant Duration for Masters
When SLOT_CYCLE AHB clock cycles have elapsed since the last arbitration, a new arbitration takes place so as to let
another master access this slave. If another master is requesting the slave bus, then the current master burst is broken.
If SLOT_CYCLE = 0, the Slot Cycle Limit feature is disabled and bursts always complete unless broken according to the
ULBT.
This limit has been placed in order to enforce arbitration so as to meet potential latency constraints of masters waiting for
slave access or in the particular case of a master performing back-to-back undefined length bursts indefinitely freezing the
arbitration.
This limit must not be too small. Unreasonably small values break every burst and the Bus Matrix arbitrates without per-
forming any data transfer. The default maximum value is usually an optimal conservative choice.
In most cases this feature is not needed and should be disabled for power saving. See
• DEFMSTR_TYPE: Default Master Type
0: No Default Master
At the end of the current slave access, if no other master request is pending, the slave is disconnected from all masters.
This results in a one-clock cycle latency for the first access of a burst transfer or for a single access.
1: Last Default Master
At the end of the current slave access, if no other master request is pending, the slave stays connected to the last master
having accessed it.
This results in not having a one-clock cycle latency when the last master tries to access the slave again.
2: Fixed Default Master
At the end of the current slave access, if no other master request is pending, the slave connects to the fixed master the
number that has been written in the FIXED_DEFMSTR field.
This results in not having a one-clock cycle latency when the fixed master tries to access the slave again.
• FIXED_DEFMSTR: Fixed Default Master
This is the number of the Default Master for this slave. Only used if DEFMSTR_TYPE is 2. Specifying the number of a mas-
ter which is not connected to the selected slave is equivalent to setting DEFMSTR_TYPE to 0.
312
31
23
15
–
–
–
7
SAM9G25
Bus Matrix Slave Configuration Registers
MATRIX_SCFG0...MATRIX_SCFG9
0xFFFFDE40 [0], 0xFFFFDE44 [1], 0xFFFFDE48 [2], 0xFFFFDE4C [3], 0xFFFFDE50 [4], 0xFFFFDE54 [5],
0xFFFFDE58 [6], 0xFFFFDE5C [7], 0xFFFFDE60 [8], 0xFFFFDE64 [9]
Read-write
30
22
14
–
–
–
6
29
21
13
–
–
5
28
20
12
–
–
4
FIXED_DEFMSTR
SLOT_CYCLE
27
19
11
–
–
3
26
18
10
–
–
2
Section 25.5.1.2 on page
25
17
–
9
–
1
DEFMSTR_TYPE
11032A–ATARM–27-Jul-11
SLOT_CYCLE
306.
24
16
–
8
0