SAM9G25 Atmel Corporation, SAM9G25 Datasheet - Page 927

• Manufacturer Part Number: SAM9G25
• Manufacturer: Atmel Corporation

Specifications of SAM9G25

• Flash (kbytes): 0 Kbytes
• Pin Count: 247
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.6.9
41.6.10
11032A–ATARM–27-Jul-11
11032A–ATARM–27-Jul-11
Write Protection Registers
Buffer Structure
Warning: No input buffer amplifier to isolate the source is included in the ADC. This must be
taken into consideration to program a precise value in the TRACKTIM field. See the product
ADC Characteristics section.
The DMA read channel is triggered each time a new data is stored in ADC_LCDR register. The
same structure of data is repeatedly stored in ADC_LCDR register each time a trigger event
occurs. Depending on user mode of operation (ADC_MR, ADC_CHSR, ADC_SEQR1,
ADC_SEQR2) the structure differs. Each data transferred to DMA buffer, carried on a half-word
(16-bit), consists of last converted data right aligned and when TAG is set in ADC_EMR register,
the 4 most significant bits are carrying the channel number thus allowing an easier post-process-
ing in the DMA buffer or better checking the DMA buffer integrity.
To prevent any single software error that may corrupt ADC behavior, certain address spaces
can be write-protected by setting the WPEN bit in the
(ADC_WPMR).
If a write access to the protected registers is detected, then the WPVS flag in the ADC Write Pro-
tect Status Register (ADC_WPSR) is set and the field WPVSRC indicates in which register the
write access has been attempted.
The WPVS flag is reset by writing the ADC Write Protect Mode Register (ADC_WPMR) with the
appropriate access key, WPKEY.
The protected registers are:
•
•
•
•
•
•
•
•
•
“ADC Mode Register” on page 930
“ADC Channel Sequence 1 Register” on page 932
“ADC Channel Sequence 2 Register” on page 933
“ADC Channel Enable Register” on page 934
“ADC Channel Disable Register” on page 935
“ADC Extended Mode Register” on page 943
“ADC Compare Window Register” on page 944
“ADC Analog Control Register” on page 946
“ADC Trigger Register” on page 947
“ADC Write Protect Mode Register”
SAM9G25
SAM9G25
927
927