ATmega88PA Automotive Atmel Corporation, ATmega88PA Automotive Datasheet - Page 154
ATmega88PA Automotive
Manufacturer Part Number
ATmega88PA Automotive
Description
Manufacturer
Atmel Corporation
- Current page: 154 of 225
- Download datasheet (4Mb)
18.10.4
154
Atmel ATtiny24/44/84 [Preliminary]
ADCSRB – ADC Control and Status Register B
• Bits 7 – BIN: Bipolar Input Mode
The gain stage is working in the unipolar mode by default, but the bipolar mode can be
selected by writing the BIN bit in the ADCSRB register. In the unipolar mode, only one-sided
conversions are supported, and the voltage on the positive input must always be larger than
the voltage on the negative input. Otherwise, the result is saturated to the voltage reference. In
the bipolar mode, two-sided conversions are supported, and the result is represented in two's
complement form. In unipolar mode, the resolution is 10 bits, and in bipolar mode the resolu-
tion is 9 bits + 1 sign bit.
• Bit 6 – ACME: Analog Comparator Multiplexer Enable
See
• Bit 5 – Res: Reserved Bit
This bit is reserved bit in the Atmel® ATtiny24/44/84, and will always read as what was written
there.
• Bit 4 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC data register.
Write logical one to ADLAR to left adjust the result. Otherwise, the result is right adjusted.
Changing the ADLAR bit will affect the ADC data register immediately, regardless of any
ongoing conversions. For a complete description of this bit, see
Data Register” on page
• Bit 3 – Res: Reserved Bit
This bit is reserved bit in the Atmel
there.
• Bits 2:0 – ADTS2:0: ADC Auto Trigger Source
If ADATE in ADCSRA is written to logical one, the value of these bits selects which source will
trigger an ADC conversion. If ADATE is cleared, the ADTS2:0 settings will have no effect. A
conversion will be triggered by the rising edge of the selected interrupt flag. Note that switch-
ing from a trigger source that is cleared to a trigger source that is set will generate a positive
edge on the trigger signal. If ADEN in ADCSRA is set, this will start a conversion. Switching to
free running mode (ADTS[2:0]=0) will not cause a trigger event, even if the ADC Interrupt Flag
is set.
Bit
0x03 (0x23)
Read/Write
Initial Value
“ADCSRB – ADC Control and Status Register B” on page
R/W
BIN
7
0
153.
ACME
R/W
6
0
R/W
®
5
–
0
ATtiny24/44/84, and will always read as what was written
ADLAR
R/W
4
0
R/W
3
–
0
ADTS2
R/W
2
0
135.
“ADCL and ADCH – ADC
ADTS1
R/W
1
0
ADTS0
R/W
0
0
7701E–AVR–02/11
ADCSRB
Related parts for ATmega88PA Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
MCU AVR 8K ISP FLSH 20MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 8K ISP FLASH 20MHZ 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 8K ISP FLASH 20MHZ 28DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
MCU AVR 8KB FLASH 20MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 8KB FLASH 20MHZ 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Atmega88p 8-bit Microcontroller With 8k Bytes In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet: