TDA8922B NXP Semiconductors, TDA8922B Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TDA8922B
Manufacturer Part Number
TDA8922B
Description
The TDA8922B is a high efficiency class-D audio power amplifier with very lowdissipation
Manufacturer
NXP Semiconductors
Datasheet
1.TDA8922B.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TDA8922BJ
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
TDA8922BTH
Manufacturer:
NXP
Quantity:
11
Part Number:
TDA8922BTH
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
TDA8922BTH/N2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
TDA8922BU/N2
Manufacturer:
NXP
Quantity:
152 970
Part Number:
TDA8922BU/N2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
9397 750 13357
Preliminary data sheet
13.7 Pumping effects
The TDA8922B amplifier can distinguish between a low-ohmic short circuit condition and
other overcurrent conditions like dynamic impedance drops of the used loudspeakers. The
impedance threshold (Z
Depending on the impedance of the short circuit the amplifier will react as follows:
In this way the TDA8922B amplifier is fully robust against short circuit conditions while at
the same time so-called audio holes as a result of loudspeaker impedance drops are
eliminated.
In a typical stereo half-bridge (Single-Ended (SE)) application the TDA8922B class-D
amplifier is supplied by a symmetrical voltage (e.g V
the amplifier is used in a SE configuration, a so-called ‘pumping effect’ can occur. During
one switching interval, energy is taken from one supply (e.g. V
energy is delivered back to the other supply line (e.g. V
voltage supply source cannot sink energy, the voltage across the output capacitors of that
voltage supply source will increase: the supply voltage is pumped to higher levels. The
voltage increase caused by the pumping effect depends on:
The pumping effect should not cause a malfunction of either the audio amplifier and/or the
voltage supply source. For instance, this malfunction can be caused by triggering of the
undervoltage or overvoltage protection or unbalance protection of the amplifier.
Best remedy for pumping effects is to use the TDA8922B in a mono full-bridge application
or in case of stereo half-bridge application adapt the power supply (e.g. increase supply
decoupling capacitors).
1. Short-circuit impedance > Z
2. Short-circuit impedance < Z
•
•
•
•
•
The maximum output current of the amplifier is regulated to 5 A, but the amplifier will
not shut-down its PWM outputs. Effectively this results in a clipping output signal
across the load (behavior is very similar to voltage clipping).
The amplifier will limit the maximum output current to 5 A and at the same time the
capacitor on the PROT pin is discharged. When the voltage across this capacitor
drops below an internal threshold voltage the amplifier will shut-down completely and
an internal timer will be started.
A typical value for the capacitor on the PROT pin is 220 pF. After a fixed time of
100 ms the amplifier is switched on again. If the requested output current is still too
high the amplifier will switch-off again. Thus the amplifier will try to switch to the
Operating mode every 100 ms. The average dissipation will be low in this situation
because of this low duty cycle. If the overcurrent condition is removed the amplifier will
remain in Operating mode once restarted.
Speaker impedance
Supply voltage
Audio signal frequency
Value of decoupling capacitors on supply lines
Source and sink currents of other channels.
Rev. 01 — 1 October 2004
th
) depends on the supply voltage used.
th
th
:
:
DD
2
SS
= +26 V and V
) and visa versa. When the
50 W class-D power amplifier
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
DD
), while a part of that
TDA8922B
SS
= 26 V). When
18 of 32