XA-S3 NXP Semiconductors, XA-S3 Datasheet - Page 34
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
XA-S3
Manufacturer Part Number
XA-S3
Description
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer
NXP Semiconductors
Datasheet
1.XA-S3.pdf
(52 pages)
1. Maximum 15pF for EA/V
2. Ports in quasi-bidirectional mode with weak pullup (applies to ALE, PSEN only during RESET).
3. Ports in PUSH-PULL mode, both pullup and pulldown assumed to be the same strength.
4. In all output modes.
5. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when
6. Measured with port in high impedance mode.
7. Measured with port in quasi-bidirectional mode.
8. Under steady state (non-transient) conditions, I
Philips Semiconductors
ABSOLUTE MAXIMUM RATINGS
DC ELECTRICAL CHARACTERISTICS
V
T
NOTES:
2000 Dec 01
amb
DD
Operating temperature under bias
Storage temperature range
Voltage on EA/V
Voltage on any other pin to V
Maximum I
Power dissipation (based on package heat transfer, not device power consumption)
I
I
I
V
V
V
V
V
V
V
C
I
I
I
SYMBOL
SYMBOL
DD
ID
PD
IL
LI
TL
XA 16-bit microcontroller
32 K/1 K OTP/ROM/ROMless, 8-channel 8-bit A/D, low voltage (2.7 V–5.5 V),
I
RAM
IL
IH
IH1
OL
OH1
OH2
IO
V
If I
test conditions.
2
C, 2 UARTs, 16 MB address range
= 2.7 V to 5.5 V, unless otherwise specified.
IN
= 0 to +70 C for commercial, T
OL
Maximum I
Maximum I
Maximum total I
is approximately 2 V.
exceeds the test condition, V
OL
Power supply current, operating
Power supply current, Idle mode
Power supply current, Power Down mode
RAM keep-alive voltage
Input low voltage
Input high voltage, except XTAL1, RST
Input high voltage to XTAL1, RST
Output low voltage, all ports, ALE, PSEN
Output high voltage, all ports, ALE, PSEN
Output high voltage, all ports ALE, PSEN
Input/Output pin capacitance
Logical 0 input current, all ports
Input leakage current, all ports
Logical 1 to 0 transition current, all ports
per I/O pin
OL
OL
PP
per port pin:
per 8-bit port:
pin to V
OL
for all outputs:
PP
SS
.
SS
PARAMETER
PARAMETER
amb
OL
= –40 C to +85 C for industrial, unless otherwise specified.
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
1
PARAMETER
15 mA
26 mA
71 mA
6
7
OL
must be externally limited as follows:
2
4
5
, CLKOUT
, CLKOUT
3
, CLKOUT
34
I
I
I
OH
I
OH
OH
5.0 V, 3.0 V, –40 to +85 C
I
I
OH
OL
OL
For both 3.0 V and 5.0 V
TEST CONDITIONS
TEST CONDITIONS
= –100 A, V
= –3.2 mA, V
= –1.0 mA, V
= 3.2 mA, V
= 1.0 mA, V
= –30 A, V
V
At V
At V
5.0 V, 30 MHz
5.0 V, 30 MHz
V
IN
V
V
5.0 V, 3.0 V
IN
DD
DD
= V
DD
DD
= 0.45 V
= 5.0 V
= 3.0 V
IL
= 5.5 V
= 2.7 V
or V
DD
DD
DD
DD
DD
DD
= 5.0 V
= 3.0 V
= 2.7 V
IH
= 4.5 V
= 4.5 V
= 2.7 V
0.7 V
MIN
–0.5
1.5
2.2
2.0
2.4
2.0
2.4
2.2
–0.5 to V
DD
–55 to +125
–65 to +150
0 to +13.0
RATING
LIMITS
1.5
15
TYP
DD
5
+0.5 V
Preliminary specification
0.22 V
MAX
–650
–250
100
150
–50
0.5
0.4
80
35
15
10
DD
XA-S3
UNIT
mA
W
V
V
C
C
UNIT
UNIT
mA
mA
pF
V
V
V
V
V
V
V
V
V
V
V
A
A
A
A
A
A