STM32W108C8 STMicroelectronics, STM32W108C8 Datasheet - Page 136
STM32W108C8
Manufacturer Part Number
STM32W108C8
Description
High-performance, IEEE 802.15.4 wireless system-on-chip with 64-Kybte Flash memory
Manufacturer
STMicroelectronics
Datasheet
1.STM32W108C8.pdf
(216 pages)
Specifications of STM32W108C8
Receive Current (w/ Cpu)
27 mA
Transmit Current (w/ Cpu, +3 Dbm Tx)
31 mA
Low Deep Sleep Current, With Retained Ram And Gpio
400 nA/800 nA with/without sleep timer
Standard Arm Debug Capabilities
Flash patch and breakpoint; data watchpoint and trace; instrumentation trace macrocell
Single Voltage Operation
2.1-3.6 V with internal 1.8 V and 1.25 V regulators
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 136 of 216
- Download datasheet (3Mb)
General-purpose timers
135/215
The delay between the rising edge on TI2 and the actual start of the counter is due to the
resynchronization circuit on the TI2 input.
Figure 41. Control circuit in Trigger mode
Slave mode: External clock mode 2 + Trigger mode
External clock mode 2 can be used in combination with another slave mode (except external
clock mode 1 and encoder mode). In this case, the ETR signal is used as external clock
input, and another input can be selected as trigger input when operating in reset mode,
gated mode or trigger mode. It is not recommended to select ETR as TRGI through the
TIM_TS bits of TIMx_SMCR register.
In the following example, the up-counter is incremented at each rising edge of the ETR
signal as soon as a rising edge of TI1 occurs:
●
●
●
A rising edge on TI1 enables the counter and sets the INT_TIMTIF flag. The counter then
counts on ETR rising edges.
The delay between the rising edge of the ETR signal and the actual reset of the counter is
due to the resynchronization circuit on ETRP input.
Configure the external trigger input circuit by programming the TIMx_SMCR register as
follows:
–
–
–
Configure the channel 1 as follows, to detect rising edges on TI:
–
–
–
–
Configure the timer in Trigger mode by writing TIM_SMS = 110 in the TIMx_SMCR
register. Select TI1 as the input source by writing TIM_TS = 101 in the TIMx_SMCR
register.
TIM_ETF = 0000: no filter.
TIM_ETPS = 00: prescaler disabled.
TIM_ETP = 0: detection of rising edges on ETR and TIM_ECE = 1 to enable the
external clock mode 2.
TIM_IC1F = 0000: no filter.
The capture prescaler is not used for triggering and does not need to be
configured.
TIM_CC1S = 01in the TIMx_CCMR1 register to select only the input capture
source.
TIM_CC1P = 0 in the TIMx_CCER register to validate the polarity (and detect
rising edge only).
Doc ID 018587 Rev 2
STM32W108C8
Related parts for STM32W108C8
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/32-BITS MICROS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Starter and extension kits for STM32W108xx microcontrollers
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet: