TLE 8264-2E Infineon Technologies, TLE 8264-2E Datasheet - Page 44
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
TLE 8264-2E
Manufacturer Part Number
TLE 8264-2E
Description
Manufacturer
Infineon Technologies
Datasheet
1.TLE_8264-2E.pdf
(94 pages)
Specifications of TLE 8264-2E
Packages
PG-DSO-36
Transceiver
High Speed CAN ISO 11898 - 5 / 3 x LIN2.0 / J2602
Voltage Regulator Output
2 x 200 mA + 400 mA
Watchdog
Standard and Window Watchdog
Quiescent Current (max.)
28 ?A (typ) Sleep Mode (5V on)
Standby Current
58 ?A (typ) Stop Mode (5V on)
10.2.2
The LIN transceiver offers a LIN Low Slope Mode for 10.4 kBaud communication and a LIN Normal Slope Mode
for 20 kBaud communication. The only difference is the behavior of the transmitter. In LIN Low Slope Mode, the
transmitter uses a lower slew rate to further reduce the EME compared to Normal Mode. This complies with SAE
J2602 requirements.
The selection is done for all transceivers at the same time so that the chip is working in either LIN Low slope Mode
or in LIN Normal Slope Mode. By default, the device works in LIN Low Slope Mode. The selection of LIN Normal
Slope Mode is done by an SPI word. The selection is accessible in SBC Normal Mode only.
10.2.3
In this mode, the LIN transceiver is completely disabled. Only an SPI command can reactivate the LIN cell. This
mode is accessible in SBC Normal, Stop, and Sleep Modes and is the default behavior in SBC Init Mode.
10.2.4
This mode, which can be used in SBC Stop, Sleep, Restart and Normal Modes by programming via SPI and is
automatically accessed in SBC Fail-Safe Mode, is used to monitor bus activities. A wake up signal on the bus
results in different behavior of the SBC, as described in
to LIN Normal Mode for communication. To enable the LIN Wakeable Mode after a wake via this LIN tranceiver,
the deticated LIN transceiver must be switched to LIN Normal Mode, LIN Receive Only Mode or LIN Off, before
switching to LIN Wakeable Mode again.
Table 8
SBC Mode
Sleep Mode
Stop Mode
Restart Mode
Fail-Safe Mode
Normal Mode
1) When not masked via SPI
Wake-Up in SBC Sleep Mode
Wake-up is possible via a LIN message (filtering time t >
Restart Mode and from there to Normal Mode the corresponding RxD pins in set to LOW, see
microcontroller is able to detect the low signal on RxD and to read the wake source out of the “Wake Register
Interrupt” register (000) via SPI. No Interrupt is generated when coming out of Sleep Mode. The µC can now switch
the CAN transceiver into LIN Normal Mode via SPI to start communication.
Wake-Up in SBC Stop Mode
In SBC Stop Mode, if a wake-up is detected, it is signaled by the INT output and by the “WK LINx” SPI bit. It is also
signaled by RxDLINx put to low.The microcontroller should set the device to SBC Normal Mode, there is no
automatic transition to Normal Mode. In Normal Mode the transceiver can be enabled via SPI.
Data Sheet
Slope Selection
LIN OFF Mode
LIN Wake Capable Mode
Action Due to a CAN Wake Up
SBC Mode after wake
Restart Mode
Stop Mode
Restart Mode
Restart Mode
Normal Mode
Vcc1µC
Ramping up
ON
Ramping up / ON
Ramping up
ON
44
Table
t
WK,bus
8. After wake-up the transceiver can be switched
), it automatically transfers the SBC into the SBC
INT
HIGH
LOW
HIGH
HIGH
LOW
1)
1)
RxD
LOW
LOW
LOW
LOW
LOW
Rev. 1.0, 2009-03-31
LIN Transceiver
TLE8264-2E
Figure
Int. Bit
WK CAN
1
1
1
1
1
19. The