UBA2021 NXP Semiconductors, UBA2021 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
UBA2021
Manufacturer Part Number
UBA2021
Description
630 V Driver Ic For Cfl And Tl Lamps
Manufacturer
NXP Semiconductors
Datasheet
1.UBA2021.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UBA2021P
Manufacturer:
PHILIPS
Quantity:
62
Part Number:
UBA2021T
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
UBA2021T/N2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
UBA2021T/N2,118
Manufacturer:
AD
Quantity:
2 900
Part Number:
UBA2021T/N2,512
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
Ignition state
The RS monitoring function changes from V
regulation to capacitive mode protection at the end of the
preheat time. Normally this results in a further frequency
decrease down to the bottom frequency f
43 kHz). The rate of change of frequency in the ignition
state is less than that in the preheat mode. During the
downward frequency sweep, the circuit sweeps through
the resonant frequency of the load. A high voltage then
appears across the lamp. This voltage normally ignites the
lamp.
Failure to ignite
Excessive current levels may occur if the lamp fails to
ignite. The IC does not limit these currents in any manner.
Transition to the burn state
Assuming that the lamp has ignited during the downward
frequency sweep, the frequency normally decreases to the
bottom frequency. The IC can transit to the burn state in
two ways:
1. In the event that the bottom frequency is not reached,
2. As soon as the bottom frequency is reached.
The bottom frequency is determined by R
2002 Aug 02
handbook, halfpage
630 V driver IC for CFL and TL lamps
For calculations refer to Chapter “Design equations”.
transition is made after reaching the ignition time t
f start
f B
Fig.5 Operation in the preheat mode.
preheat state
ignition
state
B
RREF
(approximately
time
burn state
RS(ctrl)
MGS992
and C
CF
ign
.
.
6
Feed-forward frequency
Above a defined voltage level the oscillation frequency
also depends on the supply voltage of the half-bridge
(see Fig.6). The current for the current-controlled oscillator
is in the feed-forward range derived from the current
through R
to the average value of the current through R
operating range of I
For currents beyond the operating range (i.e. between
1.0 and 1.6 mA) the feed-forward frequency is clamped. In
order to prevent feed-forward of ripple on V
filtered out. The capacitor connected to pin CP is used for
this purpose. This pin is also used in the preheat state and
the ignition state for timing (t
Capacitive mode protection
When the preheat mode is completed, the IC will protect
the power circuit against losing the zero voltage switching
condition and getting too close to the capacitive mode of
operation. This is detected by monitoring voltage V
pin RS. If the voltage is below V
turn-on of T2, then capacitive mode operation is assumed.
Consequently the frequency increases as long as the
capacitive mode is detected. The frequency decreases
down to the feed-forward frequency if no capacitive mode
is detected. Frequency modulation is achieved via pin CI.
handbook, halfpage
For calculations refer to Chapter “Design equations”.
(kHz)
f
RHV
Fig.6 Feed-forward frequency.
. The feed-forward frequency is proportional
frequency
bottom
i(RHV)
, given the lower limit set by f
ph
and t
RS(cap)
ign
Product specification
).
at the time of
UBA2021
feed-forward
I RHV (mA)
in
range
RHV
, the ripple is
MGS993
within the
RS
B
at
.