UBA2032 NXP Semiconductors, UBA2032 Datasheet
UBA2032
Available stocks
Related parts for UBA2032
UBA2032 Summary of contents
Page 1
... DATA SHEET UBA2032 Full bridge driver IC Product specification Supersedes data of 2003 Oct 24 INTEGRATED CIRCUITS 2005 Mar 24 ...
Page 2
... Input for start-up delay Adjustable oscillator frequency Predefined bridge position during start-up Adaptive non-overlap. APPLICATIONS The UBA2032 can drive (via the MOSFETs) any kind of load in a full bridge configuration The circuit is especially designed as a commutator for High Intensity Discharge (HID) lamps. ORDERING INFORMATION ...
Page 3
... STABILIZER SGND UVLO 7 ( (13) RC OSCILLATOR 8 (10 (12) BD 1.29 V bridge disable Pin numbers refer to the UBA2032T. Pin numbers in parenthesis refer to the UBA2032TS. 2005 Mar 24 EXTDR LVS 2 (2) 3 (3) LOGIC SIGNAL HIGH VOLTAGE GENERATOR LEVEL SHIFTER UBA2032T UBA2032TS 2 LOW VOLTAGE LOGIC ...
Page 4
... MOSFET 18 not connected 19 not connected 20 gate of lower left MOSFET 21 power ground 22 not connected 23 gate of lower right MOSFET 24 not connected 25 not connected 26 source of higher right MOSFET 27 floating supply voltage right 28 gate of higher right MOSFET 4 Product specification UBA2032 DESCRIPTION ...
Page 5
... MGU543 Fig.2 Pin configuration (SO24). FUNCTIONAL DESCRIPTION Supply voltage The UBA2032 is powered by a supply voltage applied to pin HV, for instance the supply voltage of the full bridge. The IC generates its own low supply voltage for the internal circuitry. Therefore an additional low voltage supply is not required. A capacitor has to be connected to pin V to obtain a ripple-free internal supply voltage ...
Page 6
... EXTDR signal with respect LVS If the supply voltage on pin V or pin HV drops below the DD reset level of power drive, the UBA2032 re-enters the start-up phase. The design equation for the bridge oscillator frequency is bridge Non-overlap time The non-overlap time is the time between turning off the conducting pair of MOSFETs and turning on the next pair ...
Page 7
... LOW LOW LOW LOW HIGH LOW LOW LOW LOW LOW HIGH LOW HIGH HIGH HIGH LOW LOW HIGH LOW LOW HIGH LOW LOW HIGH LOW LOW (5) LOW HIGH HIGH UBA2032 GLR LOW HIGH LOW HIGH LOW HIGH HIGH HIGH HIGH LOW ...
Page 8
... transient at t < 0 with respect to V LVS DC value transient at t < 0 value transient at t < 0 value transient at t < 0 value transient at t < 0.1 s repetitive note 1 8 Product specification UBA2032 MIN. MAX. UNIT 550 V 0 564 ...
Page 9
... V = 564 V FSL FSR t < 0.5 s and V = 464 V EXTDR t < 0.5 s and V = 464 V +LVS t < 0.5 s and V = 450 V LVS note 8.25 V; note Product specification UBA2032 VALUE UNIT 80 K/W 100 K/W MIN. TYP. MAX. UNIT ...
Page 10
... with respect to V LVS with respect to V LVS note 5. with +LVS EXTDR respect to V LVS with respect to V LVS 10 Product specification UBA2032 MIN. TYP. MAX. UNIT 130 180 mA 150 ...
Page 11
... Mar 24 CONDITIONS note 250 Hz and bridge +150 C amb f = 250 Hz and bridge RC(high RC(low 250 Hz bridge DD = 150 Product specification UBA2032 MIN. TYP. MAX. UNIT 100 kHz +10 % 0.38 0.4 0.42 0.01 0.94 1.02 1.10 100 ...
Page 12
... The bridge starts oscillating when the HV supply voltage exceeds the level of release power drive (typically 12 pin HV). If the supply voltage on pin HV drops below the reset level of power drive (typically pin HV), the UBA2032 enters the start-up state. R >100 LVS GHR ...
Page 13
... FSR LVS SHR >100 UBA2032T V DD GLR PGND 8 18 GLL SHL FSL 11 14 SGND GHL 12 13 Fig.6 External control configuration. 13 Product specification UBA2032 HL HR (1) R >100 LR IGNITOR ( >100 MGU547 (1) (1) ...
Page 14
... R >100 GHR 1 28 FSR SHR R>100 GLR 23 9 UBA2032TS PGND 10 21 GLL 11 20 SHL FSL 13 16 GHL 14 15 Fig.7 Application with a negative lamp voltage. 14 Product specification HL HR (1) R>100 LR IGNITOR (1) LL R>100 UBA2032 (1) (1) MGU803 ...
Page 15
... V sufficient anymore result the internal low voltage supply ( increase of the on resistance (R MOSFETs. In this case an auxiliary low voltage supply is necessary. 15 Product specification UBA2032 Q . bridge gate supply current may not and the gate drive voltage will drop resulting ...
Page 16
... REFERENCES JEDEC JEITA MS-013 16 Product specification detail 1.1 1.1 0.25 0.25 0.1 1.4 0.4 1.0 0.043 0.043 0.01 0.055 0.01 0.004 0.016 0.039 EUROPEAN PROJECTION UBA2032 SOT137 (1) Z 0.9 0 0.035 0.016 ISSUE DATE 99-12-27 03-02-19 ...
Page 17
... 2.5 scale (1) ( 0.38 0.20 10.4 5.4 7.9 0.65 0.25 0.09 10.0 5.2 7.6 REFERENCES JEDEC JEITA MO-150 detail 1.03 0.9 1.25 0.2 0.13 0.63 0.7 EUROPEAN PROJECTION Product specification UBA2032 SOT341 ( 1.1 8 0.1 o 0.7 0 ISSUE DATE 99-12-27 03-02-19 ...
Page 18
... Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 seconds to 5 seconds between 270 C and 320 C. 18 Product specification UBA2032 ...
Page 19
... However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. 9. Hot bar soldering or manual soldering is suitable for PMFP packages. 2005 Mar 24 (1) (3) , TFBGA, (8) 19 Product specification UBA2032 SOLDERING METHOD WAVE REFLOW not suitable suitable (4) not suitable suitable suitable ...
Page 20
... Product specification UBA2032 DEFINITION These products are not Philips Semiconductors ...
Page 21
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2005 All rights are reserved. Reproduction in whole or in part is prohibited ...