UBA1706 NXP Semiconductors, UBA1706 Datasheet
UBA1706
Related parts for UBA1706
UBA1706 Summary of contents
Page 1
... DATA SHEET UBA1706 Cordless telephone line interface Objective specification Supersedes data of 1999 Mar 08 File under Integrated Circuits, IC17 INTEGRATED CIRCUITS 1999 Jun 04 ...
Page 2
... APPLICATIONS Cordless base stations Mains or battery-powered telephone sets. GENERAL DESCRIPTION The UBA1706 is a BiCMOS integrated circuit intended for use in mains-powered telecom terminals. It performs all speech and line interface functions, DC mask for voltage or current regulation and electronic hook switch control. The device also includes general purpose switches. ...
Page 3
... I > (typical); line 7. LVI RGL bit CRC = (RMS) TXI = 2 mV (RMS) RXI line 3 Objective specification UBA1706 = 619 ; EHI = HIGH; SET MIN. TYP. MAX. UNIT 3.0 5.5 V 2.2 3.2 mA 110 150 A 11 140 ...
Page 4
... AGC EHI PART 2 SAGC, EHI AGC CURRENT LIMITATION SWITCH DRIVER PROTECTION 600 mV 200 nA GENERAL SWITCHES 2 SWC1, SWC2 SUPPLY PD Fig.1 Block diagram. 4 Objective specification UBA1706 19 GND 7 RXO SET R SLPE 24 SLPE REG 2 C REG V CC SLPE EHI LCC 5 TP DARL ...
Page 5
... Jun 04 handbook, halfpage LN 1 REG 2 LVI 3 RGL 4 LCC 5 6 CST UBA1706 RXO 7 AGC 8 RXI 9 EHI 10 DATA FCA031 Fig.2 Pin configuration. 5 Objective specification UBA1706 24 SLPE 23 n. n.c. 19 GND 18 SW1 17 SW2 16 n.c. 15 TXI+ 14 TXI- 13 CLK ...
Page 6
... All data given in this chapter consists of typical values, except when otherwise specified. Supply (pins V and GND; bit PD) CC The UBA1706 must be supplied with an external stabilized voltage source across pins V and GND. CC Without any signal and without any general purpose switch selected, the internal current consumption is 2 ...
Page 7
... F Fig.4 Reference voltage supply configuration UBA1706 V ref HOOK SWITCH MANAGEMENT SLPE LCC EHI R SLPE V EHI ( Objective specification UBA1706 LN I line Z SET I ZSET 619 FCA032 LN Z line I line I ZSET R exch Z SET 619 V line V exch LN FCA033 ...
Page 8
... DC line voltages (excluding the polarity guard) down to 1.2 V. With a line current below I circuit has limited transmit and receive levels. This is called the low voltage area. Figure 6 shows in more detail how the UBA1706, in association with some external components, manages the line interrupter (TN external transistor). ...
Page 9
... Acrobat reader. white to force landscape pages to be ... UBA1706 REG C REG 4.7 F EHI V EHI CURRENT REGULATION MODE MANAGEMENT I LVI CRC RGL R RGL 7. ON-HOOK Bit names are given in italics. Fig.6 Line interrupter management and DC mask regulation configuration. ...
Page 10
... Philips Semiconductors Cordless telephone line interface The UBA1706 offers the possibility to choose two kinds of regulations for the DC characteristic between line terminals LN+ and LN (see Fig.7): Voltage regulation mode Current regulation mode. handbook, halfpage V line (1) (2) I low I knee (1) Low voltage area. (2) Small slope (determined ...
Page 11
... This minimizes the contribution of the IC to the current waveform during pulse dialling or register recall. When the UBA1706 is in power-down mode (bit PD at logic 1), transistor TP is forced off whatever the DARL voltage applied at pin EHI. ...
Page 12
... The suppression also depends on the accuracy of the match between Z line. The anti-sidetone network for the UBA1706 (see Fig.15) ) attenuates the receiving signal from the line before it enters the receiving amplifier. The attenuation is almost constant over the whole audio frequency range. ...
Page 13
... PIN RAGC2, SAGC AGC) AND The UBA1706 performs automatic line loss compensation. The AGC varies the gain of the transmit amplifier and the gain of the receive amplifier in accordance with the DC line current. The control range is 6.5 dB (which corresponds roughly to a line length of 5.5 km for a 0.5 mm diameter twisted-pair copper cable with a DC resistance of 176 /km and an average attenuation of 1 ...
Page 14
... Cordless telephone line interface General purpose switches (pins SWI1 and SWI2; bits SWC1 and SWC2) The UBA1706 is equipped with two general purpose open-collector switches, which short circuit pins SWI1 and SWI2 to ground. These switches are controlled by bits SWC1 and SWC2, respectively, and have an operating voltage limited ...
Page 15
... AGC inhibited D3 1: AGC enabled must be set to logic amplifier enabled D1 1: amplifier muted 0: normal operating mode D2 1: power-down mode must be set to logic Objective specification UBA1706 STATE AT ADDRESS POWER-UP RESET (AD1, AD0) = (0, (AD1, AD0) = (0, ...
Page 16
... Jun 04 CONDITIONS MIN. GND GND GND continuous GND during switching GND GND see Fig.12 bit SWCn = see Fig.12 amb 40 25 CONDITIONS VALUE 100 16 Objective specification UBA1706 MAX. UNIT 0.4 5.5 V 0.4 12.0 V 0.4 13.2 V 0.4 12.0 V 0.4 13 150 454 mW +125 C ...
Page 17
... The line current value can be calculated from the – SET SLPE LN SLPE I = --------------------------------------------------------------------------------------------- - line R SET 1999 Jun 04 (4) (3) (2) ( value as follows: LN where R is the resistive part SET SET Fig.12 Safe operating area. 17 Objective specification UBA1706 FCA036 SLPE (V) ...
Page 18
... I = 140 mA line VA(SLPE REG +75 C amb 500 bit CRC = 0 bit CRC = 1 I > line knee LVI bit CRC = 1 RGL 18 Objective specification UBA1706 = 619 ; EHI = HIGH; SET TYP. MAX. UNIT 5.5 V 2.2 3.2 mA 110 150 A 2.9 3.2 V 1.2 V 1.8 V 3.0 3.3 V 4. ...
Page 19
... F; psophometrically weighted (P53 curve (RMS) 36.9 RXI f = 300 to 3400 +75 C amb (RMS) RXI V = 12.5 mV (RMS) RXI V = 19.5 mV (RMS); RXI line 19 Objective specification UBA1706 TYP. MAX. UNIT 0.4 0. 11.6 12.6 dB 0.3 dB ...
Page 20
... RAGC2 = 1 bits SAGC = 1; RAGC1 = 1; RAGC2 = 1 bit AGC = 140 mA line bit SWCn = 0 700 2 mA < I < 20 mA; SWIn bit SWCn = 1 2 5.5 V GND CC input level = HIGH 1 20 Objective specification UBA1706 TYP. MAX. UNIT 81 dBVp 80 dB 6 ...
Page 21
... SU; DATA t input data to clock hold time HD; DATA handbook, full pagewidth t SU;DATA t HD;DATA CLK DATA START 1999 Jun 04 PARAMETER D4 AD1 Fig.13 Serial bus timing diagram. 21 Objective specification UBA1706 MIN. MAX. 0 300 kHz 1 s 0.1 s 1 SU;EN ...
Page 22
... 1N4148 BUX86 from V LN microcontroller LN GND SWI2 SWI1 EHI DATA TXI 15 V TXI TXI 14 UBA1706 LCC CST LVI REG AGC C LCC C REG C LVI C CST R LVI 6.8 pF 4.7 F 470 ON-HOOK TN ON-HOOK ...
Page 23
... To improve EMC performance; necessary for stability. (4) To improve stability only in current regulation mode. R ast1 260 SWI2 SWI1 TXIP TXI 15 100 nF C TXIM TXI 14 UBA1706 100 VCC LCC CST LVI REG TP DARL MPSA92 (4) C REG ...
Page 24
... SOT340-1 1999 Jun 2.5 scale (1) ( 0.20 8.4 5.4 7.9 0.65 0.09 8.0 5.2 7.6 REFERENCES JEDEC EIAJ MO-150AG 24 Objective specification UBA1706 detail 1.03 0.9 1.25 0.2 0.13 0.1 0.63 0.7 EUROPEAN ISSUE DATE PROJECTION SOT340 ...
Page 25
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 25 Objective specification UBA1706 ...
Page 26
... Philips for any damages resulting from such improper use or sale. 1999 Jun 04 SOLDERING METHOD WAVE not suitable (2) suitable (3)(4) not recommended (5) not recommended 26 Objective specification UBA1706 (1) REFLOW suitable suitable suitable suitable suitable ...
Page 27
... Philips Semiconductors Cordless telephone line interface 1999 Jun 04 NOTES 27 Objective specification UBA1706 ...
Page 28
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + ...