DSPIC30F2012 Microchip Technology Inc., DSPIC30F2012 Datasheet - Page 147

• Manufacturer Part Number: DSPIC30F2012
• Description: Dspic30f2011/2012/3012/3013 High-performance Digital Signal Controllers
• Manufacturer: Microchip Technology Inc.

20.0
This section provides an overview of dsPIC30F electrical characteristics. Additional information will be provided in future
revisions of this document as it becomes available.
For detailed information about the dsPIC30F architecture and core, refer to “dsPIC30F Family Reference Manual”
(DS70046).
Absolute maximum ratings for the dsPIC30F family are listed below. Exposure to these maximum rating conditions for
extended periods may affect device reliability. Functional operation of the device at these or any other conditions above
the parameters indicated in the operation listings of this specification is not implied.
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to V
Voltage on V
Voltage on MCLR with respect to V
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports (Note 2)....................................................................................................200 mA
20.1
TABLE 20-1:
© 2006 Microchip Technology Inc.
†
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
Note 1: Voltage spikes below V
Note:
V
2: Maximum allowable current is a function of device maximum power dissipation. See Table 20-2 for P
DD
4.5-5.5V
4.5-5.5V
3.0-3.6V
3.0-3.6V
2.5-3.0V
ELECTRICAL CHARACTERISTICS
DC Characteristics
Thus, a series resistor of 50-100 should be used when applying a “low” level to the MCLR/V
than pulling this pin directly to V
All peripheral electrical characteristics are specified. For exact peripherals available on specific
devices, please refer to the Family Cross Reference Table.
Range
DD
with respect to V
OPERATING MIPS VS. VOLTAGE
IK
OK
(V
DD
SS
I
(V
< 0 or V
pin (Note 2)................................................................................................................250 mA
O
pin ...........................................................................................................................300 mA
< 0 or V
SS
-40°C to 125°C
-40°C to 125°C
-40°C to 85°C
-40°C to 85°C
-40°C to 85°C
Temp Range
I
SS
SS
SS
> V
(†)
......................................................................................................... -0.3V to +5.5V
........................................................................................................ 0V to +13.25V
at the MCLR/V
O
dsPIC30F2011/2012/3012/3013
(except V
DD
> V
) .......................................................................................................... ±20 mA
SS
DD
.
) ...................................................................................................±20 mA
DD
and MCLR) (Note 1) .................................... -0.3V to (V
PP
pin, inducing currents greater than 80 mA, may cause latch-up.
dsPIC30FXXX-30I
30
20
10
—
—
Max MIPS
dsPIC30FXXX-20E
DS70139E-page 145
20
15
—
—
—
PP
DD
pin, rather
+ 0.3V)
DMAX
.