DSPIC33FJ64GP306 Microchip Technology Inc., DSPIC33FJ64GP306 Datasheet - Page 226
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
DSPIC33FJ64GP306
Manufacturer Part Number
DSPIC33FJ64GP306
Description
High-performance, 16-bit Digital Signal Controllers
Manufacturer
Microchip Technology Inc.
Datasheet
1.DSPIC33FJ64GP306.pdf
(324 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC33FJ64GP306-I/PT
Manufacturer:
Microchi
Quantity:
130
Company:
Part Number:
DSPIC33FJ64GP306-I/PT
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
DSPIC33FJ64GP306-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC33FJ64GP306A-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC33FJ64GP306A-I/MR
Manufacturer:
Microchip Technology
Quantity:
135
Company:
Part Number:
DSPIC33FJ64GP306A-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC33FJ64GP306AT-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC33FJ64GP306T-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
dsPIC33FJXXXGPX06/X08/X10
19.3.18
The SLOT<3:0> status bits in the DCISTAT SFR
indicate the current active time slot. These bits will cor-
respond to the value of the frame sync generator
counter. The user may poll these status bits in software
when a DCI interrupt occurs to determine what time slot
data was last received and which time slot data should
be loaded into the TXBUF registers.
19.3.19
The CSDOM control bit controls the behavior of the
CSDO pin during unused transmit slots. A given trans-
mit time slot is unused if it’s corresponding TSEx bit in
the TSCON SFR is cleared.
If the CSDOM bit is cleared (default), the CSDO pin will
be low during unused time slot periods. This mode will
be used when there are only two devices attached to
the serial bus.
If the CSDOM bit is set, the CSDO pin will be tri-stated
during unused time slot periods. This mode allows
multiple devices to share the same CSDO line in a
multi-channel application. Each device on the CSDO
line is configured to only transmit data during specific
time slots. No two devices will transmit data during the
same time slot.
19.3.20
Digital Loopback mode is enabled by setting the
DLOOP control bit in the DCICON1 SFR. When the
DLOOP bit is set, the module internally connects the
CSDO signal to CSDI. The actual data input on the
CSDI I/O pin will be ignored in Digital Loopback mode.
19.3.21
When an underflow occurs, one of two actions can
occur, depending on the state of the Underflow mode
(UNFM) control bit in the DCICON1 SFR. If the UNFM
bit is cleared (default), the module will transmit ‘0’s on
the CSDO pin during the active time slot for the buffer
location. In this operating mode, the Codec device
attached to the DCI module will simply be fed digital
‘silence’. If the UNFM control bit is set, the module will
transmit the last data written to the buffer location. This
operating mode permits the user to send continuous
data to the Codec device without consuming CPU
overhead.
DS70286A-page 224
SLOT STATUS BITS
CSDO MODE BIT
DIGITAL LOOPBACK MODE
UNDERFLOW MODE CONTROL BIT
19.4
The frequency of DCI module interrupts is dependent
on the BLEN<1:0> control bits in the DCICON2 SFR.
An interrupt to the CPU is generated each time the set
buffer length has been reached and a shadow register
transfer takes place. A shadow register transfer is
defined as the time when the previously written TXBUF
values are transferred to the transmit shadow registers
and new received values in the receive shadow
registers are transferred into the RXBUF registers.
19.5
19.5.1
The DCI module has the ability to operate while in
Sleep mode and wake the CPU when the CSCK signal
is supplied by an external device (CSCKD = 1). The
DCI module will generate an asynchronous interrupt
when a DCI buffer transfer has completed and the CPU
is in Sleep mode.
19.5.2
If the DCISIDL control bit is cleared (default), the mod-
ule will continue to operate normally even in Idle mode.
If the DCISIDL bit is set, the module will halt when Idle
mode is asserted.
19.6
The AC-Link protocol is a 256-bit frame with one 16-bit
data slot, followed by twelve 20-bit data slots. The DCI
module has two operating modes for the AC-Link pro-
tocol. These operating modes are selected by the
COFSM<1:0> control bits in the DCICON1 SFR. The
first AC-Link mode is called ‘16-bit AC-Link mode’ and
is selected by setting COFSM<1:0> = 10. The second
AC-Link mode is called ‘20-bit AC-Link mode’ and is
selected by setting COFSM<1:0> = 11.
19.6.1
In the 16-bit AC-Link mode, data word lengths are
restricted to 16 bits. Note that this restriction only
affects the 20-bit data time slots of the AC-Link proto-
col. For received time slots, the incoming data is simply
truncated to 16 bits. For outgoing time slots, the four
Least Significant bits of the data word are set to ‘0’ by
the module. This truncation of the time slots limits the
ADC and DAC data to 16 bits but permits proper data
alignment in the TXBUF and RXBUF registers. Each
RXBUF and TXBUF register will contain one data time
slot value.
DCI Module Interrupts
DCI Module Operation During CPU
Sleep and Idle Modes
AC-Link Mode Operation
DCI MODULE OPERATION DURING
CPU SLEEP MODE
DCI MODULE OPERATION DURING
CPU IDLE MODE
16-BIT AC-LINK MODE
© 2007 Microchip Technology Inc.