TA8493AFG TOSHIBA Semiconductor CORPORATION, TA8493AFG Datasheet

no-image

TA8493AFG

Manufacturer Part Number
TA8493AFG
Description
3-phase Full Wave Brushless Dc Motor Driver Ic For Cd-rom Drives
Manufacturer
TOSHIBA Semiconductor CORPORATION
Datasheet
3-Phase Full Wave Brushless DC Motor Driver IC for CD-ROM Drives
been developed for use in CD-ROM drive spindle motors. The
TA8493F/FG/ AF/AFG/ BF/BFG contain in its upper stage a
discrete power transistor (P-ch-MOS) and uses direct PWM
control system, which enables the IC to provide superior thermal
efficiency.
dispersion of the heat generated inside the package, making it
possible to suppress heat concentration.
Features
These 3-phase, full-wave, brushless DC motor driver ICs have
Furthermore, the multi-chip structure of this device facilitates
TA8493FG/AFG/BFG:
The TA8493FG/AFG/BFG is a Pb-free product.
The following conditions apply to solderability:
*Solderability
1.
2.
Multi-chip structure (3 × 2SJ465 chips built-in)
Direct PWM control system
Drive system: 120°drive system (TA8493F/FG/BF/BFG)
Built-in current limiter: I
Built-in reversing brake/short brake functions
FG signal output (using hall element output signal)
Built-in hall bias
Built-in thermal shutdown circuit
Package: MFP-30
Use of Sn-37Pb solder bath
*solder bath temperature = 230°C
*dipping time = 5 seconds
*number of times = once
*use of R-type flux
Use of Sn-3.0Ag-0.5Cu solder bath
*solder bath temperature = 245°C
*dipping time = 5 seconds
*the number of times = once
*use of R-type flux
TA8493F/FG, TA8493AF/AFG,
: 180°drive system (TA8493AF/AFG)
Toshiba Bipolar Linear Integrated Circuit Multi-Chip
LIM
= 0.7 A (typ.) (at R
TA8493BF/BFG
F
= 0.33 Ω)
1
Weight: 0.63 g (typ.)
2006-3-6

Related parts for TA8493AFG

TA8493AFG Summary of contents

Page 1

Toshiba Bipolar Linear Integrated Circuit Multi-Chip TA8493F/FG, TA8493AF/AFG, 3-Phase Full Wave Brushless DC Motor Driver IC for CD-ROM Drives These 3-phase, full-wave, brushless DC motor driver ICs have been developed for use in CD-ROM drive spindle motors. The TA8493F/FG/ AF/AFG/ ...

Page 2

Block Diagram − − − FGO ...

Page 3

PIN Assignment Terminal Terminal No. Symbol GND2 N.C. 10 FGO 11 BRK − ...

Page 4

Absolute Maximum Ratings Characteristics Power Supply Voltage Output Current Power Dissipation Junction Temperature Operating Temperature Storage Temperature Note1: unmounted Operating Voltage Range Characteristics Power Supply Voltage Electrical Characteristics Characteristics Supply Voltage Input Current Common Mode Hall Amp. Input Voltage Range ...

Page 5

Characteristics Output Resistance (upper side) Saturation Voltage Output Circuit (lower side) Cut-off Current (upper side) Cut-off Current (lower side) Input Voltage (H) Mode Select Circuit Input Voltage (L) Input Current Hysteresis Voltage Output Voltage FG Amp. (H) Output Voltage (L) ...

Page 6

Function Table <Forward> = −(H − ...

Page 7

Hall Signal − Output Voltage GND + Output Current − 2006-3-6 ...

Page 8

Functional Description This 3-phase, full wave brushless DC motor driver of the direct PWM control type. • Control amp input circuit V The common mode input voltage ranges for both V Relation between control input and PWM ...

Page 9

When V > one of three modes (reverse rotation, reversing brake or short brake mode) can be selected by C ref setting the MS and BRK pins appropriately. <Function> < ref BRK H H Forward ...

Page 10

When stopping the motor using reversing brake mode MS: L, BRK ref Forward mode Note3: For an explanation of the Reversing Brake mode stopping sequence, refer to the explanation of the reverse rotation detection circuit. ...

Page 11

Hall element bias circuit The hall element bias current is turned off when the driver standby state. Make sure that the negative hall bias line is connected to the HB pin. The remaining voltage is as ...

Page 12

Reverse rotation detection circuit By comparing the two phases of the Hall element signal, this circuit detects a state where the phases are inverted, at which time the torque is reduced to 0. The detection accuracy is determined by ...

Page 13

Output circuit (upper stage) This circuit uses the system to chop the lower power transistors and resurrect coil current through upper stage diodes. The upper-stage power transistors consist of Pch-MOS transistors (2SJ465), which give high torque efficiency ...

Page 14

Current limiter circuit The current limit value is determined by the equation below. 0.3 ∼ − I [A] (typ.) LIM R + 0.1 F This circuit cut off lower power transistors compulsorily when filtered V (0.3 V) PWM signal ...

Page 15

External Parts Terminal No. C Power supply line oscillation prevention 1 C Power supply line noise prevention 2 C Power supply line noise prevention 3 C Filter 4 Forward/reverse changeover gain C 5 adjustment C Triangular wave oscillation 6 R ...

Page 16

Test Circuit CC1 CC2 INS ( ( • ...

Page 17

INH CMRH HB INC ( ( ...

Page 18

V OFF (F) OFF (R) LIM ( ( ...

Page 19

(U) SAT ( ( ( • R ...

Page 20

( ( • ...

Page 21

(H) MS (L) INS BRK ( ( ( ...

Page 22

OFG (H) OFG ( ( • OFG (H) ...

Page 23

Application Circuit − − − FGO Contol C ...

Page 24

Package Dimensions Weight: 0.63 g (typ.) 24 2006-3-6 ...

Page 25

Notes on Contents 1. Block Diagrams Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for explanatory purposes. 2. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of ...

Page 26

Points to remember on handling of ICs (1) Over current Protection Circuit Over current protection circuits (referred to as current limiter circuits) do not necessarily protect ICs under all circumstances. If the Over current protection circuits operate against the over ...

Page 27

27 2006-3-6 ...

Related keywords