SI3211 ETC, SI3211 Datasheet - Page 33
![no-image](/images/no-image-200.jpg)
SI3211
Manufacturer Part Number
SI3211
Description
PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION
Manufacturer
ETC
Datasheet
1.SI3211.pdf
(122 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI3211-FM
Manufacturer:
SILICON
Quantity:
640
Part Number:
SI3211-FM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
SI3211-KT
Manufacturer:
IDT
Quantity:
1 599
Part Number:
SI3211-KT
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Enhanced FSK Waveform Generation
Silicon revisions C and higher support enhanced FSK
generation capabilities, which can be enabled by setting
FSKEN = 1 (direct Register 108, bit 6) and REN = 1
(direct Register 32, bit 6). In this mode, the user can
define mark (1) and space (0) attributes once during
initialization by defining indirect registers 99–104. The
user need only indicate 0-to-1 and 1-to-0 transitions in
the information stream. By writing to FSKDAT (direct
Register 52), this mode applies a 24 kHz sample rate to
tone generator 1 to give additional resolution to timers
and frequency generation. Application Note 32 gives
detailed instructions on how to implement FSK in this
mode. Additionally, sample source code is available
from Silicon Laboratories upon request.
Tone Generator Interrupts
Both the active and inactive timers can generate their
own interrupt to signal “on/off” transitions to the
software. The timer interrupts for tone generator 1 can
be individually enabled by setting the O1AE and O1IE
bits (direct Register 21, bits 0 and 1, respectively).
Timer interrupts for tone generator two are O2AE and
O2IE (direct Register 21, bits 2 and 3, respectively). A
pending interrupt for each of the timers is determined by
reading the O1AP, O1IP, O2AP, and O2IP bits in the
Interrupt Status 1 register (direct Register 18, bits 0
through 3, respectively).
Ringing Generation
The ProSLIC provides fully programmable internal
balanced ringing with or without a dc offset to ring a
wide variety of terminal devices. All parameters
associated with ringing are software programmable:
ringing frequency, waveform, amplitude, dc offset, and
Gen. 1
Output
OSS1
Signal
Tone
O1E
0,1
...
...
, OAT1
Figure 19. Tone Generator Timing Diagram
0,1
...
Preliminary Rev. 1.11
...
, O IT1
ringing cadence. Both sinusoidal and trapezoidal ringing
waveforms are supported, and the trapezoidal crest
factor is programmable. Ringing signals of up to 88 V
peak or more can be generated, enabling the ProSLIC
to drive a 5 REN (1380
loop lengths of 2000 feet (160
Ringing Architecture
The ringing generator architecture is nearly identical to
that of the tone generator. The sinusoid ringing
waveform is generated using an internal two-pole
resonance
frequency and amplitude. However, since ringing
frequencies are very low compared to the audio band
signaling
generated at a 1 kHz rate instead of 8 kHz.
The ringing generator has two timers that function the
same as for the tone generator timers. They allow on/off
cadence settings up to 8 sec on/ 8 sec off. In addition to
controlling ringing cadence, these timers control the
transition into and out of the ringing state. Table 28
summarizes the list of registers used for ringing
generation.
Note: Tone generator 2 should not be enabled concurrently
with the ringing generator due to resource sharing
within the hardware.
Si3210/Si3211/Si3212
0,1
frequencies,
...
oscillator
...
, OAT1
circuit
the
+ 40 F) ringer load across
0,1
...
) or more.
ringing
with
programmable
waveform
...
...
33
is