IDT7201LA35J IDT, Integrated Device Technology Inc, IDT7201LA35J Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT7201LA35J
Manufacturer Part Number
IDT7201LA35J
Description
IC MEM FIFO 512X9 35NS 32-PLCC
Manufacturer
IDT, Integrated Device Technology Inc
Series
7200r
Datasheet
1.IDT7202LA15J.pdf
(14 pages)
Specifications of IDT7201LA35J
Function
Asynchronous
Memory Size
4.6K (512 x 9)
Access Time
35ns
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
32-PLCC
Configuration
Dual
Density
4.5Kb
Access Time (max)
35ns
Word Size
9b
Organization
512x9
Sync/async
Asynchronous
Expandable
Yes
Bus Direction
Uni-Directional
Package Type
LCC
Clock Freq (max)
Not RequiredMHz
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (min)
4.5V
Operating Supply Voltage (max)
5.5V
Supply Current
80mA
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
32
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Data Rate
-
Lead Free Status / RoHS Status
Not Compliant, Contains lead / RoHS non-compliant
Other names
7201LA35J
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT7201LA35J
Manufacturer:
IDT
Quantity:
8 831
Company:
Part Number:
IDT7201LA35J
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Part Number:
IDT7201LA35J
Manufacturer:
IDT
Quantity:
20 000
Company:
Part Number:
IDT7201LA35J8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT7201LA35JI
Manufacturer:
IDT
Quantity:
12 388
Part Number:
IDT7201LA35JI
Manufacturer:
IDT
Quantity:
20 000
SIGNAL DESCRIPTIONS
INPUTS:
DATA IN (D
CONTROLS:
RESET (RS)
state. During reset, both internal read and write pointers are set to the first
location. A reset is required after power up before a write operation can take
place. Both the Read Enable (R) and Write Enable (W) inputs must be
in the HIGH state during the window shown in Figure 2, (i.e., t
before the rising edge of RS) and should not change until t
the rising edge of RS. Half-Full Flag (HF) will be reset to HIGH after
Reset (RS).
WRITE ENABLE (W)
is not set. Data set-up and hold times must be adhered to with respect to the rising
edge of the Write Enable (W). Data is stored in the RAM array sequentially and
independently of any on-going read operation.
operation, the Half-Full Flag (HF) will be set to LOW and will remain set until the
difference between the write pointer and read pointer is less than or equal to
one half of the total memory of the device. The Half-Full Flag (HF) is then reset
by the rising edge of the read operation.
write operations. Upon the completion of a valid read operation, the Full
Flag (FF) will go HIGH after t
is full, the internal write pointer is blocked from W, so external changes in W will
not affect the FIFO when it is full.
READ ENABLE (R)
the Empty Flag (EF) is not set. The data is accessed on a First-In/First-Out basis,
independent of any ongoing write operations. After Read Enable (R) goes
HIGH, the Data Outputs (Q
the next Read operation. When all data has been read from the FIFO, the Empty
Flag (EF) will go LOW, allowing the “final” read cycle but inhibiting further read
operations with the data outputs remaining in a high impedance state. Once a
valid write operation has been accomplished, the Empty Flag (EF) will go HIGH
after t
read pointer is blocked from R so external changes in R will not affect the FIFO
when it is empty.
FIRST LOAD/RETRANSMIT (FL/RT)
grounded to indicate that it is the first loaded (see Operating Modes). In the Single
IDT7201L/7201LA/7202LA CMOS ASYNCHRONOUS FIFO
256 x 9, 512 x 9 and 1,024 x 9
Data inputs for 9-bit wide data.
Reset is accomplished whenever the Reset (RS) input is taken to a LOW
A write cycle is initiated on the falling edge of this input if the Full Flag (FF)
After half of the memory is filled and at the falling edge of the next write
To prevent data overflow, the Full Flag (FF) will go LOW, inhibiting further
A read cycle is initiated on the falling edge of the Read Enable (R) provided
This is a dual-purpose input. In the Depth Expansion Mode, this pin is
WEF
and a valid Read can then begin. When the FIFO is empty, the internal
0
– D
8
)
0
RFF
– Q
, allowing a valid write to begin. When the FIFO
8
) will return to a high impedance condition until
RSR
after
RSS
6
Device Mode, this pin acts as the retransmit input. The Single Device Mode is
initiated by grounding the Expansion In (XI).
Retransmit Enable control (RT) input is pulsed LOW. A retransmit operation will
set the internal read pointer to the first location and will not affect the write pointer.
Read Enable (R) and Write Enable (W) must be in the HIGH state during
retransmit. This feature is useful when less than 256/512/1,024 writes are
performed between resets. The retransmit feature is not compatible with the
Depth Expansion Mode and will affect the Half-Full Flag (HF), depending on
the relative locations of the read and write pointers.
EXPANSION IN (XI)
an operation in the single device mode. Expansion In (XI) is connected to
Expansion Out (XO) of the previous device in the Depth Expansion or Daisy
Chain Mode.
OUTPUTS:
FULL FLAG (FF)
write pointer is one location less than the read pointer, indicating that the
device is full. If the read pointer is not moved after Reset (RS), the Full-Flag
(FF) will go LOW after 256 writes for IDT7200, 512 writes for the IDT7201A and
1,024 writes for the IDT7202A.
EMPTY FLAG (EF)
the read pointer is equal to the write pointer, indicating that the device is
empty.
EXPANSION OUT/HALF-FULL FLAG (XO/HF)
Expansion In (XI) is grounded, this output acts as an indication of a half-full
memory.
operation, the Half-Full Flag (HF) will be set LOW and will remain set until the
difference between the write pointer and read pointer is less than or equal
to one half of the total memory of the device. The Half-Full Flag (HF) is then
reset by using rising edge of the read operation.
Out (XO) of the previous device. This output acts as a signal to the next device
in the Daisy Chain by providing a pulse to the next device when the previous
device reaches the last location of memory.
DATA OUTPUTS (Q
whenever Read (R) is in a HIGH state.
The IDT7200/7201A/7202A can be made to retransmit data when the
This input is a dual-purpose pin. Expansion In (XI) is grounded to indicate
The Full Flag (FF) will go LOW, inhibiting further write operation, when the
The Empty Flag (EF) will go LOW, inhibiting further read operations, when
This is a dual-purpose output. In the single device mode, when
After half of the memory is filled and at the falling edge of the next write
In the Depth Expansion Mode, Expansion In (XI) is connected to Expansion
Data outputs for 9-bit wide data. This data is in a high impedance condition
0
– Q
COMMERCIAL, INDUSTRIAL AND MILITARY
8
)
TEMPERATURE RANGES
OCTOBER 22, 2008