UPD160040 NEC, UPD160040 Datasheet
![no-image](/images/manufacturer_photos/0/4/470/nec_sml.jpg)
UPD160040
Related parts for UPD160040
UPD160040 Summary of contents
Page 1
... D/A converter and 8-by-2 external power modules. Because the output dynamic range is as large as V common electrode is rendered unnecessary. Also able to deal with dot-line inversion, n-line inversion and column line inversion when mounted on a single side, this source driver is equipped with a built-in 8-bit D/A converter circuit whose odd output pins and even output pins respectively output gray scale voltages of differing polarity ...
Page 2
BLOCK DIAGRAM STHR R,/L CLK STB C C MODE POL21 POL22 POL V -V ...
Page 3
PIN CONFIGURATION ( PD160040N-xxx) (Copper Foil Surface, Face-up) STHL SRC ORC V ...
Page 4
... Input The contents of the data register are transferred to the latch circuit at the rising edge. In addition, at the falling edge, the gray scale voltage is supplied to the driver necessary to ensure input of one pulse per horizontal period. Input SRC = H: High-through-rate period (large current consumption) ...
Page 5
Pin Symbol Pin Name MODE Output reset control POL21, Data inversion POL22 V Driver voltage select SEL TEST Test V -V -corrected power supplies Logic power supply DD1 V Driver power supply DD2 V Logic ground SS1 ...
Page 6
RELATIONSHIP BETWEEN INPUT DATA AND OUTPUT VOLTAGE VALUE The PD160040 incorporates a 8-bit D/A converter whose odd output pins and even output pins output respectively gray scale voltages of differing polarity with respect to the LCD’s counter electrode voltage. ...
Page 7
Figure 5 2. -Corrected Voltages and Ladder Resistors Ratio rn Ratio1 r0 3.58 V ’’ ’ 3.58 255 r253 r2 3.58 V ’ ’’ 254 r3 3.58 r252 r0 ...
Page 8
Figure 5 3. Relationship between Input Data and Output Voltage (POL21, POL22 = L) (1/2) (Output voltage 1) V – 0.2 V DD2 Data Output voltage1 Data ' 00H V V7 40H ...
Page 9
Figure 5 3. Relationship between Input Data and Output Voltage (POL21, POL22 = L) (2/2) (Output voltage 2) 0.5 V DD2 Data Data Output voltage2 00H V " V8 40H V " V12 0 64 01H V " V9 41H ...
Page 10
RELATIONSHIP BETWEEN INPUT DATA AND OUTPUT PIN Data format: 8 bits x 2 RGBs (6 dots) Input width: 48 bits (2-pixel data) (1) R,/ (right shift) Output Data ...
Page 11
RELATIONSHIP BETWEEN MODE, STB, SRC, ORC, POL, AND OUTPUT WAVEFORM When MODE = H or open and STB = H, all outputs are reset (short) and the gray-scale voltage is output to LCD in synchronization with the falling edge ...
Page 12
MODE = L STB High through rate period SRC Low through rate period ORC High output resistance period Low output resistance period POL S 2n–1 Voltage selected form Voltage selected form V Hi ...
Page 13
ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings ( Parameter Symbol Logic part supply voltage V DD1 Driver part supply voltage V DD2 Logic part input voltage V I1 Driver part input voltage V I2 Logic part ...
Page 14
... The TYP. values refer to an all black or all white input pattern. The MAX. value refers to the measured values in the dot checkerboard input pattern. 4. Refers to the current consumption per driver when cascades are connected under the assumption of SXGA single-sided mounting (10 units). Switching Characteristics (T ...
Page 15
Timing Requirements ( + Parameter Symbol Clock pulse width PW CLK Clock pulse high period PW CLK (H) Clock pulse low period PW CLK (L) Data setup time t SETUP1 Data hold time t ...
Page 16
CLK(L) CLK CLK( CLK t t SETUP2 HOLD2 STHR (1st Dr SETUP1 HOLD1 373 INVALID ...
Page 17
CLK(L) CLK CLK( CLK t t SETUP2 HOLD2 STHR (1st Dr SETUP1 HOLD1 373 INVALID ...
Page 18
RECOMMENDED MOUNTING CONDITIONS The following conditions must be met for mounting conditions of the PD160040. For more details, refer to the Semiconductor Device Mounting Technology Manual (C10535E). Please consult with our sales offices in case other mounting process is ...
Page 19
... HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction connection is provided to the input pins possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry ...