UPD78F9418A NEC, UPD78F9418A Datasheet - Page 39
UPD78F9418A
Manufacturer Part Number
UPD78F9418A
Description
(UPD7894xxA) 8-Bit Single Chip Microcontrollers
Manufacturer
NEC
Datasheet
1.UPD78F9418A.pdf
(319 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UPD78F9418A
Manufacturer:
NEC
Quantity:
1 831
Part Number:
UPD78F9418AGC
Manufacturer:
NEC
Quantity:
20 000
Company:
Part Number:
UPD78F9418AGC-8BT-A
Manufacturer:
RENESAS
Quantity:
800
Company:
Part Number:
UPD78F9418AGC-8BT-A
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
UPD78F9418AGK-9EU
Manufacturer:
NEC
Quantity:
20 000
Company:
Part Number:
UPD78F9418AGK-9EU-A
Manufacturer:
Renesas Electronics America
Quantity:
10 000
- Current page: 39 of 319
- Download datasheet (3Mb)
www.DataSheet4U.com
2.2.14 AV
when the A/D converter is not used).
2.2.15 RESET
2.2.16 X1, X2
2.2.17 XT1, XT2
2.2.18 V
2.2.19 V
2.2.20 V
program is written or verified.
the user program may not run correctly.
This pin is the A/D converter ground potential pin. Always keep it at the same potential as the V
This pin inputs an active-low system reset signal.
These pins are used to connect a crystal resonator for main system clock oscillation.
To supply an external clock, input the clock to X1 and input the inverted signal to X2.
These pins are used to connect a crystal resonator for subsystem clock oscillation.
To supply an external clock, input the clock to XT1 and input the inverted signal to XT2.
V
V
A high voltage should be applied to this pin when the flash memory programming mode is set and when the
Handle the pins in either of the following ways.
• Independently connect a 10 kΩ pull-down resistor.
• Switch this pin to be directly connected to the dedicated flash programmer in programming mode or to V
If the wiring between the V
DD0
SS0
V
SS1
is the ground potential pin for ports, while the V
is the positive power supply pin for ports, while V
DD0
SS0
PP
SS
in normal operation mode using a jumper on the board.
( µ µ µ µ PD78F9418A only)
, V
, V
SS1
DD1
PP
pin and V
SS0
CHAPTER 2 PIN FUNCTIONS
User’s Manual U13952EJ3V0UD
or V
SS1
pin is long, or external noise is superimposed on the V
SS1
DD1
is the ground potential pin for other than ports.
is the positive power supply pin for other than ports.
SS0
pin (even
PP
SS0
pin,
39
or
Related parts for UPD78F9418A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16BIT MCU, 128K FLASH, 8K RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT UC, 32K FLASH, 1KB RAM, LCD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 60K FLASH, 3KB RAM, CAN
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 128K FLASH, 7K RAM, LQFP
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 4K FLASH, 128B RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet: