DS26334 Dallas Semiconductor, DS26334 Datasheet - Page 88
![no-image](/images/manufacturer_photos/0/1/182/dallas_semiconductor_sml.jpg)
DS26334
Manufacturer Part Number
DS26334
Description
E1/T1/J1 Shortand Long-Haul Line Interface Unit
Manufacturer
Dallas Semiconductor
Datasheet
1.DS26334.pdf
(121 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS26334
Manufacturer:
TEMIC
Quantity:
138
Company:
Part Number:
DS26334G+
Manufacturer:
MAXIM
Quantity:
23
Company:
Part Number:
DS26334GA3+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS26334GNA3+
Manufacturer:
DALLAS
Quantity:
85
Register Name:
Register Description:
Register Address (LIUs 1–8):
Register Address (LIUs 9–16):
Bit #
Name
Default
Bits 5 to 3: Transmit Error Insertion Rate (TEIR[2:0]). These three bits indicate the rate at which errors are
inserted in the output data stream. One out of every 10
of 0 disables error insertion at a specific rate. A TEIR[2:0] value of 1 result in every 10th bit being inverted. A
TEIR[2:0] value of 2 result in every 100th bit being inverted. Error insertion starts when this register is written to
with a TEIR[2:0] value that is nonzero. If this register is written to during the middle of an error insertion process,
the new error rate will be started after the next error is inserted.
Bit 2: Bit Error Insertion Enable (BEI). When 0, single bit error insertion is disabled. When 1, single bit error
insertion is enabled.
Bit 1: Transmit Single Error Insert (TSEI). This bit causes a bit error to be inserted in the transmit data stream if
manual error insertion is disabled (MEIMS = 0) and single bit error insertion is enabled. A 0 to 1 transition causes a
single bit error to be inserted. For a second bit error to be inserted, this bit must be set to 0, and back to 1. Note: If
MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be
inserted.
Bit 0: Manual Error Insert Mode Select (MEIMS). When 0, error insertion is initiated by the TSEI register bit.
When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is
one, changing the state of this bit may cause a bit error to be inserted.
Register Name:
Register Description:
Register Address (LIUs 1–8):
Register Address (LIUs 9–16):
Bit #
Name
Default
Bit 3: Performance Monitoring Update Status (PMS). This bit indicates the status of the receive performance
monitoring register (counters) update. This bit will transition from low to high when the update is completed. PMS is
asynchronously forced low when the LPMU bit (PMUM = 0) or RPMU signal (PMUM=1) goes low.
Bit 1: Bit Error Count (BEC). When 0, the bit error count is zero. When 1, the bit error count is one or more.
Bit 0: Out Of Synchronization (OOS). When 0, the receive pattern generator is synchronized to the incoming
pattern. When 1, the receive pattern generator is not synchronized to the incoming pattern.
—
—
7
0
7
0
—
—
6
0
6
0
TEICR
Transmit Error Insertion Control Register
08h
28h
BSR
BERT Status Register
0Ch
2Ch
TEIR2
DS26334 3.3V, 16-Channel, E1/T1/J1 Short/Long-Haul Line Interface Unit
—
5
0
5
0
TEIR1
88 of 121
—
4
0
4
0
n
bits is inverted. TEIR[2:0] is the value n. A TEIR[2:0] value
TEIR0
PMS
3
0
3
0
BEI
—
0
0
2
2
TSEI
BEC
1
0
1
0
MEIMS
OOS
0
0
0
0