XC3S1200E-5FT256C Xilinx, Inc., XC3S1200E-5FT256C Datasheet - Page 109
XC3S1200E-5FT256C
Manufacturer Part Number
XC3S1200E-5FT256C
Description
XC3S1200E-5FT256C
Manufacturer
Xilinx, Inc.
Datasheet
1.XC3S1200E-5FT256C.pdf
(233 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 109 of 233
- Download datasheet (4Mb)
Bitstream Generator (BitGen) Options
For additional information, refer to the “Configuration Bit-
stream Generator (BitGen) Settings” chapter in UG332.
Various Spartan-3E FPGA functions are controlled by spe-
cific bits in the configuration bitstream image. These values
Table 69: Spartan-3E FPGA Bitstream Generator (BitGen) Options
DS312-2 (v3.8) August 26, 2009
Product Specification
ConfigRate
StartupClk
UnusedPin
DONE_cycle
GWE_cycle
GTS_cycle
LCK_cycle
Option Name
R
Pins/Function
Configuration,
shift registers,
Configuration
Configuration
Configuration
Configuration
Configuration
All flip-flops,
Block RAM,
LUT RAMs,
All I/O pins,
Unused I/O
and SRL16
DONE pin,
Affected
Startup
Startup
Startup
Startup
DCMs,
CCLK,
Pins
12, 25, 50
Pulldown
1, 2, 3, 4,
1, 2, 3, 4,
1, 2, 3, 4,
0, 1, 2, 3,
(default)
Pullnone
UserClk
NoWait
Values
1, 3, 6,
Pullup
4, 5, 6
Done
Keep
Done
Keep
Cclk
Jtag
5, 6
5, 6
5, 6
Sets the approximate frequency, in MHz, of the internal oscillator using for Master
Serial, SPI, and BPI configuration modes. The internal oscillator powers up at its lowest
frequency, and the new setting is loaded as part of the configuration bitstream. The
software default value is 1 (~1.5 MHz) starting with ISE 8.1, Service Pack 1.
Default. The CCLK signal (internally or externally generated) controls the startup
sequence when the FPGA transitions from configuration mode to the user mode. See
Start-Up.
A clock signal from within the FPGA application controls the startup sequence when
the FPGA transitions from configuration mode to the user mode. See Start-Up. The
FPGA application supplies the user clock on the CLK pin on the
STARTUP_SPARTAN3E primitive.
The JTAG TCK input controls the startup sequence when the FPGA transitions from
the configuration mode to the user mode. See Start-Up.
Default. All unused I/O pins and input-only pins have a pull-down resistor to GND.
All unused I/O pins and input-only pins have a pull-up resistor to the VCCO_# supply
for its associated I/O bank.
All unused I/O pins and input-only pins are left floating (Hi-Z, high-impedance,
three-state). Use external pull-up or pull-down resistors or logic to apply a valid signal
level.
Selects the Configuration Startup phase that activates the FPGA’s DONE pin. See
Start-Up.
Selects the Configuration Startup phase that asserts the internal write-enable signal to
all flip-flops, LUT RAMs and shift registers (SRL16). It also enables block RAM read
and write operations. See Start-Up.
Waits for the DONE pin input to go High before asserting the internal write-enable
signal to all flip-flops, LUT RAMs and shift registers (SRL16). Block RAM read and
write operations are enabled at this time.
Retains the current GWE_cycle setting for partial reconfiguration applications.
Selects the Configuration Startup phase that releases the internal three-state control,
holding all I/O buffers in high-impedance (Hi-Z). Output buffers actively drive, if so
configured, after this point. See Start-Up.
Waits for the DONE pin input to go High before releasing the internal three-state
control, holding all I/O buffers in high-impedance (Hi-Z). Output buffers actively drive,
if so configured, after this point.
Retains the current GTS_cycle setting for partial reconfiguration applications.
The FPGA does not wait for selected DCMs to lock before completing configuration.
If one or more DCMs in the design have the STARTUP_WAIT attribute set to TRUE,
the FPGA waits for such DCMs to acquire their respective input clock and assert their
LOCKED output. This setting selects the Configuration Startup phase where the FPGA
waits for the DCMs to lock.
www.xilinx.com
are specified when creating the bitstream image with the
Bitstream Generator (BitGen) software.
Table 69
FPGAs.
provides a list of all BitGen options for Spartan-3E
Description
Functional Description
109
Related parts for XC3S1200E-5FT256C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
1000000 SYSTEM GATE 1.2 VOLT FPGA
Manufacturer:
Xilinx, Inc.
Datasheet:
Part Number:
Description:
Spartan-3E FPGA Family
Manufacturer:
Xilinx, Inc.
Datasheet:
Part Number:
Description:
XC95144 In-System Programmable CPLD
Manufacturer:
Xilinx, Inc.
Part Number:
Description:
XC95144 In-System Programmable CPLD
Manufacturer:
Xilinx, Inc.
Part Number:
Description:
XC95144XL High Performance CPLD
Manufacturer:
Xilinx, Inc.
Part Number:
Description:
High-performance CPLD. Speed 5ns pin-to-pin delay.
Manufacturer:
Xilinx, Inc.
Part Number:
Description:
High-performance CPLD. Speed 10ns pin-to-pin delay.
Manufacturer:
Xilinx, Inc.
Part Number:
Description:
128 MACROCELL 1.8V ZERO POWER ISP CPLD
Manufacturer:
Xilinx, Inc.
Part Number:
Description:
CPLD, CoolRunner-II Family, CMOS Process, 256 Macro Cells, 256 Reg., 106 User I/Os, 1.8V Supply, 5 Speed Grade, 132BGA
Manufacturer:
Xilinx, Inc.