LM3S1138 Luminary Micro, Inc, LM3S1138 Datasheet - Page 125
![no-image](/images/no-image-200.jpg)
LM3S1138
Manufacturer Part Number
LM3S1138
Description
Lm3s1138 Arm Microcontroller
Manufacturer
Luminary Micro, Inc
Datasheet
1.LM3S1138.pdf
(491 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3S1138-EQC50-A2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1138-EQC50-A2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1138-IBZ50-A2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1138-IBZ50-A2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1138-IQC50
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1138-IQC50-A2
Manufacturer:
Texas Instruments
Quantity:
135
Part Number:
LM3S1138-IQC50-A2
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
LM3S1138-IQC50-A2T
Manufacturer:
TI/德州仪器
Quantity:
20 000
- Current page: 125 of 491
- Download datasheet (6Mb)
7.2.7
7.3
7.3.1
July 26, 2008
register (see “Interrupts and Status” on page 125) and by looking for state data in the non-volatile
memory (see “Non-Volatile Memory” on page 124).
When the HIB signal deasserts, enabling the external regulator, the external regulator must reach
the operating voltage within t
Interrupts and Status
The Hibernation module can generate interrupts when the following conditions occur:
■
■
■
All of the interrupts are ORed together before being sent to the interrupt controller, so the Hibernate
module can only generate a single interrupt request to the controller at any given time. The software
interrupt handler can service multiple interrupt events by reading the HIBMIS register. Software can
also read the status of the Hibernation module at any time by reading the HIBRIS register which
shows all of the pending events. This register can be used at power-on to see if a wake condition
is pending, which indicates to the software that a hibernation wake occurred.
The events that can trigger an interrupt are configured by setting the appropriate bits in the HIBIM
register. Pending interrupts can be cleared by writing the corresponding bit in the HIBIC register.
Initialization and Configuration
The Hibernation module can be set in several different configurations. The following sections show
the recommended programming sequence for various scenarios. The examples below assume that
a 32.768-kHz oscillator is used, and thus always show bit 2 (CLKSEL) of the HIBCTL register set
to 1. If a 4.194304-MHz crystal is used instead, then the CLKSEL bit remains cleared. Because the
Hibernation module runs at 32 kHz and is asynchronous to the rest of the system, software must
allow a delay of t
Timing” on page 121). The registers that require a delay are listed in a note in “Register Map” on page
126 as well as in each register description.
Initialization
The clock source must be enabled first, even if the RTC will not be used. If a 4.194304-MHz crystal
is used, perform the following steps:
1.
2.
If a 32.678-kHz oscillator is used, then perform the following steps:
1.
2.
The above is only necessary when the entire system is initialized for the first time. If the processor
is powered due to a wake from hibernation, then the Hibernation module has already been powered
Assertion of WAKE pin
RTC match
Low battery detected
Write 0x40 to the HIBCTL register at offset 0x10 to enable the crystal and select the divide-by-128
input path.
Wait for a time of t
other operations with the Hibernation module.
Write 0x44 to the HIBCTL register at offset 0x10 to enable the oscillator input.
No delay is necessary.
HIB_REG_WRITE
XOSC_SETTLE
HIB_TO_VDD
after writes to certain registers (see “Register Access
for the crystal to power up and stabilize before performing any
Preliminary
.
LM3S1138 Microcontroller
125
Related parts for LM3S1138
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LM3-100K-TR](/images/no-image3.png)
Part Number:
Description:
Inductor: Molded: 10u: 10%: 30M: 7.9: 440m: Axial: T/R
Manufacturer:
Inductor Supply, Inc.
![LM3-R15](/images/no-image3.png)
Part Number:
Description:
Molded Inductor
Manufacturer:
Inductor Supply, Inc.
Datasheet:
![LM3-PWN1-01-N1](/images/no-image3.png)
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
![LM3-PBL1-01-N1](/images/no-image3.png)
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
![LM3-EWN1-01-N1-MT](/images/no-image3.png)
Part Number:
Description:
Specification For Cotco Led Lamp
Manufacturer:
Marktech Optoelectronics
Datasheet:
![LM3S1110](/images/no-image3.png)
Part Number:
Description:
Lm3s1110 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1133](/images/no-image3.png)
Part Number:
Description:
Lm3s1133 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1150](/images/no-image3.png)
Part Number:
Description:
Lm3s1150 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1162](/images/no-image3.png)
Part Number:
Description:
Lm3s1162 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1165](/images/no-image3.png)
Part Number:
Description:
Lm3s1165 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1332](/images/no-image3.png)
Part Number:
Description:
Lm3s1332 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1435](/images/no-image3.png)
Part Number:
Description:
Lm3s1435 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1439](/images/no-image3.png)
Part Number:
Description:
Lm3s1439 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet: