NL10276bc28_05d NEC, NL10276bc28_05d Datasheet
NL10276bc28_05d
Related parts for NL10276bc28_05d
NL10276bc28_05d Summary of contents
Page 1
DESCRIPTION The NL10276BC28-05D is a TFT (thin film transistor) active-matrix color liquid crystal display (LCD) module comprising an amorphous silicon TFT attached to each signal electrode, a driving circuit, and a backlight. The NL10276BC28-05D ...
Page 2
... TFT array glass substrate and a color filter glass substrate. After the driver LSIs are connected to the panel, the backlight assembly is attached to the back side of the panel. RGB (red, green, blue) data signals from a source system are modulated into a form suitable for active-matrix addressing by the onboard signal processor and sent to the driver LSIs, which in turn address the individual TFT cells ...
Page 3
CHARACTERISTICS (at room temperature) Item Display area Drive system Display colors Number of pixels Pixel arrangement Pixel pitch Module size Weight Contrast ratio Viewing angle (more than the contrast ratio of 10:1) Designed viewing direction Color gamut Response time ...
Page 4
GENERAL SPECIFICATIONS Item Module size Display area Number of pixels Dot pitch Pixel pitch Pixel arrangement Display colors Weight ABSOLUTE MAXIMUM RATINGS Parameter Supply voltage Logic input voltage Lamp voltage Storage temp. Operating temp. Relative humidity (RH) www.DataSheet4U.com Absolute ...
Page 5
ELECTRICAL CHARACTERISTICS (1) Logic, LCD Driving Parameter Supply voltage Ripple voltage Differential input “L” threshold voltage Differential input “H” threshold voltage Differential input voltage Common mode voltage Terminating resistor Supply current Note: Checker flag pattern (in EIAJ ED-2522) (2) ...
Page 6
... Signals* * The termination of the signal line is connected to resistance 100 Notes: 1. Logic signals (synchronous signals and control signals) must be “0” voltage (V), when V applied. If input voltage to signal lines is higher than 0.3 V, the internal circuit will be damaged. 2. The supply voltage for input signals should be the same ...
Page 7
... GND 18 GND Note: GND is a signal ground for logic and LCD driving. GND is connected to FG (frame ground) inside the module. Remarks: Connect all pins (except 3 and 4) to avoid noise. Use 100 CN1: Figure from socket view 20 4 DataSheet U ...
Page 8
... DataSheet U .com BHR-03VS-1 J.S.T. Trading Company, Ltd. Low-voltage terminal (The cable color is gray.) Nonconnection High-voltage terminal (The cable color is white.) must be connected correctly. If they are not connected correctly, the user may get hurt and L THC63LVDF63A (Thine) TA0 Note 1 TA1 Y0P · Y0M · ...
Page 9
DISPLAY COLORS vs. INPUT DATA SIGNALS Display Colors Basic colors Black Blue Red Magenta Green Cyan Yellow White Red gray-scale Black dark bright Red Green gray-scale Black www.DataSheet4U.com dark bright Green Blue gray-scale Black dark bright Blue Note: Colors ...
Page 10
INPUT SIGNAL TIMINGS (1) Input Signal Specifications for the LCD Controller Parameter CLK Frequency Rise, fall Duty Hsync Period Display period Front porch Pulse width Back porch Hsync-CLK timing CLK-Hsync timing DE-CLK timing CLK-DE timing Rise, fall Vsync Period ...
Page 11
... Definition of Input Signal Timing for the LCD Controller <Vertical> Vsync Note Display period DE <Horizontal> www.DataSheet4U.com Note Display period DE Vsync Hsync Notes: 1. “Display period” does not exist as signals. 2. These values are in the output of THC63LVDF64A. (Refer to CONNECTING THE THC63LVDF63A) 4 DataSheet U .com tv tvp tvb tvd thp thb ...
Page 12
Input Signal Timing Chart V IH CLK V 50% cci V IL DATA (R0 R5 (G0 G5) V 50% cci (B0 B5 50% cci V IL www.DataSheet4U.com V 50% CLK ...
Page 13
... DE Vsync Hsync DE DATA DE DATA www.DataSheet4U.com Hsync CLK DE DATA Note: These values are in the output of the THC63LVDF64A (refer to CONNECTING THE THC63LVDF63A). 4 DataSheet U .com tvb 768 H (fixed) tvp ····· ····· ····· ...
Page 14
Display Position of Input Data (0, 766) D (0, 767) www.DataSheet4U.com 14 4 DataSheet U .com (X, 1) ...
Page 15
LVDS RECEIVER (1) Input Signal Specifications Parameter CLK frequency Bit 0 position Bit 1 position Bit 2 position Bit 3 position Bit 4 position Bit 5 position Bit 6 position (2) Input Signal Timing Chart CK+ CK– The present ...
Page 16
OPTICAL CHARACTERISTICS Parameter Contrast ratio Luminance Luminance uniformity Reference data Parameter Contrast ratio Color gamut Viewing Horizontal angle range Vertical Response time Notes: 1. The luminance is measured after the module has been working for 20 minutes, with all ...
Page 17
Luminance uniformity is calculated using the following formula. Luminance uniformity = 5. Definitions of viewing angles are as follows. www.DataSheet4U.com 6. Definition of response time is as follows. 4 DataSheet U .com Maximum Luminance Minimum Luminance Column 171 ...
Page 18
RELIABILITY TESTS Test Item High temperature/humidity operation Note 1 Heat cycle (operation) Note 1 Thermal shock (nonoperation) Note 1 Vibration (nonoperation) Notes 1, 2 Mechanical shock (nonoperation) Notes 1, 2 ESD (operation) Notes 1, 3 Dust (operation) Note 1 ...
Page 19
... As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning not pull the interface connectors in or out while the LCD module is operating. e) Put the module display side down on a flat horizontal plane. ...
Page 20
Cautions about module characteristics a) Do not apply a fixed-pattern data signal for a long time to the module. It may cause image sticking. Please use screen savers if the display pattern is fixed for a long time. ...
Page 21
OPENING) (4.5) (285.696) (ACTIVE AREA) 4 – 3.5 (13) (80) (13) (94) Notes: 1. Tolerance of the dimensions not shown is 0.5 mm. 2. The torque on a mounting screw should never exceed ...
Page 22
DEPTH 6 a: Insulation sheet (PET, t0. 1) 4.1 32.2 5.1 11 7.3 0 10.2 3 Material Information Light guide: > ...
Page 23
MEMO www.DataSheet4U.com 4 DataSheet U .com Data Sheet EN0484EJ1V1DS00 NL10276BC28-05D 23 www.DataSheet4U www.DataSheet www.DataSheet www.DataSheet 4U.com 4U 4U .com .com .com ...
Page 24
... To minimize risks of damage or injury to persons or property arising from a defect in an NEC electronic component containment, and anti-failure features ...