NL128102AC20_07 NEC, NL128102AC20_07 Datasheet
NL128102AC20_07
Related parts for NL128102AC20_07
NL128102AC20_07 Summary of contents
Page 1
Vertical screen expansion (Multi-scan), Incorporated backlight with inverter DESCRIPTION NL128102AC20- TFT (thin film transistor) active matrix color liquid crystal display (LCD) comprising amorphous silicon TFT attached to each signal electrode, a driving circuit and ...
Page 2
... CNTSTB CNTSEL POWC OFF GND V DDB BRTC BRTH BRTL ACA 1 GNDB 1 GNDB is connected to the module frame ground. 2 AMP LCD timing controller 1024 lines converter Inverter NL128102AC20-07 Analog H-driver 1920 lines TFT-LCD panel H:1280 3 ( V:1024 1920 lines ...
Page 3
OUTLINE OF CHARACTERISTICS (at room temperature) Display area 257.3 (H) 205.8 (V)mm Drive system a-Si TFT active matrix Display colors Full-color Number of pixels 1280 1024 Pixel arrangement RGB vertical stripe Pixel pitch 0.201 (H) 0.201 (V)mm Module size 310.0 ...
Page 4
GENERAL SPECIFICATIONS Item Module size 310.0 0.5(H) Display area 257.28 (H) Number of pixels 1280 (H) Dot pitch 0.067 (H) Pixel pitch 0.201 (H) Pixel arrangement RGB(Red, Green, Blue) vertical stripe Display colors Full-color Weight 1200 (max.) note : A ...
Page 5
ELECTRICAL CHARACTERISTICS (1) Logic/LCD driving/Backlight Parameter Symbol V CC Supply voltage DDB Logic input "L" voltage V Logic input "H" voltage V Logic input "L" current 1 I IL1 Logic input "H" current 1 I IH1 Logic ...
Page 6
SUPPLY VOLTAGE SEQUENCE Voltage 0< 0< (Synchronous signals, Control signals) CAUTION Wrong power sequence may damage the module. (1) Logic signals (synchronous signals and control signals) should be "0" voltage (V), when V higher than 0 input to ...
Page 7
... CN1 : MRF03-6R-SMT (coaxial type) Adaptable socket : MRF03-2 6P-1.27 (For cable type) or MRF03-6PR-SMT (For board to board type) Supplier : HIROSE ELECTRIC CO., LTD. Coaxial cable : UL20537PF75VLAS Supplier : HITACHI CO., LTD. note : A coaxial cable shield should be connected with GND. Pin No. Symbol Pin No. 1 CLK 4 2 Hsync 5 ...
Page 8
... Symbol Pin No. 1 GND 8 2 CNTSEL 9 3 CNTDAT 10 4 CNTSTB 11 5 GND 12 6 CNTCLK 13 7 CPSEL note : N.C. (No Connection) should be open. <Connector location: Rear view> 1 CN3 11 8 Symbol <Figure from socket view> CLAMP 13 12 GND FIELD GND N.C. GND 6 CN1 1 Connector 12 insert direction ...
Page 9
... Positive Power control signal H or open : Logic, LCD power (note1) BRTH/BRTL – Pins for backlight brightness control Connect 10 k variable resistor (note2) or voltage control (note3). BRTC Positive Backlight ON/OFF control signal H or open : Backlight on L ACA Positive Luminance control signal ...
Page 10
... BRTH < connection of the variable resistor to pins > note3 : In case of voltage control for brightness by BRTH/BRTL, at first, set BRTH to be "0 V". And BRTL input voltage can control the brightness. When BRTL input voltage is "1 V" the luminance become maximum. ...
Page 11
Serial communication timing and waveform D0 CNTDAT CNTSTB CNTCLK Parameter Symbol CLK pulse width twck CLK frequency fclk DATA setup-time tdst DATA hold-time tdhl Latch-pulse width twlp Latch setup-time tlst Rise / fall time tr, tf CNTDATA CNTCLK CNTSTB ...
Page 12
Table 1. CNTDAT COMPOSITION Data Data name D0 VEX3 Expansion mode D1 VEX2 Expansion mode D2 VEX1 Expansion mode D3 VEX0 Expansion mode D4 VD10 Vertical display position (MSB) D5 VD9 Vertical display position D6 VD8 Vertical display position D7 ...
Page 13
Table 2. Display mode (VEX3 to VEX0 ; 4 bit) VEX3 VEX2 VEX1 VEX0 Vertical magnification ...
Page 14
Table 4. Clock (CLK) delay (DELAY6 to DELAY0 ; 7 bit Delay (note 5) value (note 5) 00H 7.0 ns 2CH 01H 7.6 ns 2DH 02H 8.2 ns 2EH 03H 8.8 ns ...
Page 15
MOD1 MOD0 Upper limit of VD6 to VD0 CLK-delay setting (HEXADECIMAL note 8 : This delay value is typical 25˚C, V power supply, the delay will be changed also. ...
Page 16
Table 6. Display horizontal position (HD8 to HD0; 9 bit) HD8 HD7 HD6 HD5 HD4 • • • • • • • • ...
Page 17
... This LCD module has the function of expanding vertical direction as shown in Table 1. And expanding horizontal direction is possible by setting input CLK frequency which is equivalent to the magnification necessary to make this CLK outside of this LCD module. DISPLAY IMAGE of after two pages is display example, when DE function is default and HD and VD are set to most suitable frequency ...
Page 18
SETTING SERIAL DATA FOR EXPANSION Input signal Mode CLK Hsync Vsync [MHz] [kHz] [Hz] SXGA 107.50 64.603 59.929 135.00 78.125 72.005 XGA 65.000 48.363 60.004 75.000 56.476 70.069 79.000 58.088 72.980 78.750 60.023 75.029 SVGA 36.000 35.156 56.25 40.000 37.879 ...
Page 19
DISPLAY IMAGE (a) XGA MODE (1024 768) (1280 SXGA Holizontal = Vertical = (b) SVGA MODE (800 600) Holizontal = Vertical = (c) VGA MODE (640 480) Holizontal = Vertical = (d) 9801 MODE (640 400) Holizontal = Vertical = ...
Page 20
INPUT SIGNAL TIMING (1) SXGA-MODE (Standard) – Without use serial communication (CNTSEL = "H" or OPEN) Name CLK Frequency Rise / fall Duty Hsync Period Display Front-porch Pulse-width Back-porch Pulse-width + Back-porch CLK-Hsync timing hold / setup time V-Hsync timing ...
Page 21
Without use serial communication (CNTSEL = "H" or OPEN) CLK GND 1 Hsync Vsync Hsync 1 2.2 V (min.) ...
Page 22
Hsync Display period <Vertical> Vsync Display period (NTSC/PAL) Vsync Field First field Vsync Hsync Field 1H(min.) 1H(min thp thb thd tv tvp tvb tvd Second field First field First field 1H(min.) NL128102AC20-07 thf tvf Second field 1H(min.) ...
Page 23
Timing for generating CLAMP signal internally Hsync Display period CLAMP MOD1 MOD0 tA [CLK NTSC / PAL 16 note 1 : Exclude noises on analog RGB signal. ...
Page 24
INPUT SIGNAL AND DISPLAY POSITION (SXGA STANDARD TIMING) (1) DELSEL="L" 1023 ...
Page 25
DELSEL="H" CLK DATA INVALID DE Hsync DE DATA INVALID Vsync Hsync DATA INVALID DE NL128102AC20-07 tds thpd VALID tvp+tvb VALID INVALID tdh INVALID INVALID 25 ...
Page 26
... As the surface of polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning not pull the interface connectors in or out while the LCD module is operating. t Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care. ...
Page 27
Liquid Crystal Display has following specific characteristics. These are not defects or malfunction. The display condition of LCD module may be affected by the ambient temperature. The LCD module uses cold cathode tube for backlight. The optical characteristics, like luminance ...
Page 28
OUTLINE DRAWING : Front View (Unit in mm) (4) (5) (5) (4) 4- 3.5 note 1 : The values in parentheses are for reference. note 2 : The torque of mounting screw should be 0.392 N•m (4 kgf•cm) less. 28 ...
Page 29
OUTLINE DRAWING : Rear View (Unit in mm) (88.5) note 1 : The values in parentheses are for reference. note 2 : The torque of mounting screw should be 0.392 N•m (4 kgf•cm) less. NL128102AC20-07 (55.0) (29.0) (97.1) 29 ...
Page 30
NL128102AC20-07 ...
Page 31
NL128102AC20-07 31 ...
Page 32
... No part of this document may be copied in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device ...