ta8492p TOSHIBA Semiconductor CORPORATION, ta8492p Datasheet
ta8492p
Related parts for ta8492p
ta8492p Summary of contents
Page 1
... TOSHIBA Bipolar Linear Integrated Circuit Three-Phase Full-Wave Brushless DC Motor Driver IC The TA8492P/ three-phase full-wave supply voltage control motor driver IC. Features Output current 1 (max) x Supply voltage control motor driver x CW/CCW/STOP function x Operating voltage range (opr 0~ (opr.) TA8492PG: The TA8492PG is Pb-free product. ...
Page 2
... Stop Function Output High Impedance 2 TA8492P/PG 2004-07-27 ...
Page 3
... (source current) SAT ( (sink current) SAT ( ( ( CMRH V STP TA8492P/PG Min Typ. Max Unit 5.0 7 6.0 9 1.35 1 0.4 0 400 ...
Page 4
... Ha (min). Make sure that the input amplitude p 0.4 V. However, keep the voltage as close possible (Lower) voltage. To reduce switching noise, connect a snubber capacitor to the S 160°C (typ.) (according to design specification TA8492P/PG 2004-07-27 ...
Page 5
... V RV and GND pins. Do not connect an input resistor to CC will cause an output function error. Make sure the amplitude is p and GND lines since the IC may be destroyed S CC Recommended Remarks Value 4 4 4.7 PF (Note 3) (Note TA8492P/PG (Stop mode) are narrow, STP 2004-07-27 ...
Page 6
... V/5.99 V V/V CC 3ST (6.01 V/5.99 V V/V CC 3ST (6.01 V/5.99 V V/V CC 3ST GND GND GND GND (6.01 V/5.99 V), check that the output function is at High level TA8492P/PG GND GND V CC 2004-07-27 ...
Page 7
... GND GND (6.01 V/5.99 V) and check that the output function is “L” GND GND TA8492P/PG 2004-07-27 ...
Page 8
... GND GND (6.01 V/5.99 V) and check the output function. GND. 3ST , (6.01 V/5.99 V), fix the output function, then check (6.01 V/5.99 V) and check that the output function is forward mode. 8 TA8492P/PG . 2004-07-27 ...
Page 9
... L V GND 3ST GND Measure the I gap between V x CMRH CMRH (6.01 V/5.99 V) and check that the output function is reverse mode GND GND and 8.5 V. CMRH 9 TA8492P/PG 2004-07-27 ...
Page 10
... Application Circuit 3ST FRC TSD TA8492P/ GND 2004-07-27 ...
Page 11
... Package Dimensions Weight: 1.11 g (typ.) 11 TA8492P/PG 2004-07-27 ...
Page 12
... If the power supply is not equipped with sink capability, the power and output pins may exceed the maximum rating. The counter-electromotive force of the motor will vary depending on the conditions of use and the features of the motor. Therefore make sure there will be no damage to or operational problem in the IC, and no damage to or operational errors in peripheral circuits caused by counter-electromotive force. 12 TA8492P/PG 2004-07-27 ...
Page 13
... The products described in this document are subject to the foreign exchange and foreign trade laws. x TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. 13 TA8492P/PG 030619EBA 2004-07-27 ...