tda8563aq NXP Semiconductors, tda8563aq Datasheet
tda8563aq
Related parts for tda8563aq
tda8563aq Summary of contents
Page 1
... DATA SHEET TDA8563AQ 2 40 W/2 power amplifier with diagnostic facility Product specification Supersedes data of 1997 Feb 20 File under Integrated Circuits, IC01 INTEGRATED CIRCUITS stereo BTL car radio 2001 Feb 21 ...
Page 2
... Reverse polarity safe Electrostatic discharge protection No switch-on/switch-off plop Flexible leads Low thermal resistance. GENERAL DESCRIPTION The TDA8563AQ is an integrated class-B output amplifier in a 13-lead single-in-line (SIL) power package. It contains 2 40 W/2 The device is primarily developed for car radio and across the load P applications ...
Page 3
... VA 2.3 k power stage 20 GND1 GND2 power ground (substrate) Fig.1 Block diagram. 3 Product specification TDA8563AQ TDA8563AQ 4 output 1A PROTECTIONS Load dump Soar Thermal Short - circuit Reverse polarity 6 output 1B 11 mode switch stand-by reference voltage mute 12 diagnostic DIAGNOSTIC ...
Page 4
... DIAG Fig.2 Pin configuration. 2001 Feb 21 FUNCTIONAL DESCRIPTION The TDA8563AQ contains two identical amplifiers and can DESCRIPTION be used for bridge applications. The gain of each amplifier is fixed at 26 dB. Special features of the device are as follows. Mode select switch (pin 11) Standby: low supply current Mute: input signal suppressed Operating: normal on condition ...
Page 5
... EMPERATURE DETECTION When the virtual junction temperature T pin 12 will become continuously low. O PEN COLLECTOR OUTPUT Pin open collector output, which allows pin 12 of more devices being tied together Fig.4 Short-circuit waveform. 5 Product specification TDA8563AQ reaches 150 C, vj MGA722 t t ...
Page 6
... R thermal resistance from junction to case (see Fig.5) th(j-c) handbook, halfpage 2001 Feb 21 CONDITIONS during 50 ms; t PARAMETER output 1 output 2 virtual junction 2.2 K/W 2.2 K/W 0.2 K/W case Fig.5 Equivalent thermal resistance network. 6 Product specification TDA8563AQ MIN. MAX 2 7 +150 40 +85 150 VALUE 40 1 ...
Page 7
... V the DC output voltage P 2001 Feb 21 CONDITIONS note 14 note 2 note 2 mute/operating any short-circuit or clipping = and AC operating Product specification TDA8563AQ MIN. TYP. 6.0 14.4 115 8.5 15 7.0 3.3 7.0 0 0 MAX. UNIT 18 V 180 ...
Page 8
... 0.6 V; note 1 12 THD = 0.5%; P with respect dB; note note 3 note 3 note 3 note 4 note 5 note 6 note 7 note Product specification TDA8563AQ MIN. TYP 13 13 0.1 2 20000 ...
Page 9
... PARAMETER P output power o THD total harmonic distortion 2001 Feb measured in Fig.6; unless otherwise specified. amb CONDITIONS THD = 0.5% THD = 10% THD = 30% THD = 0.5%; V THD = 10 Product specification TDA8563AQ MIN. TYP. MAX 13 13 0.1 UNIT ...
Page 10
... To avoid high energy switching pulses which can feedback to the inputs it is advisable to ensure that the value of the resistor at pin 2001 Feb 21 mode switch 11 3 470 TDA8563AQ reference voltage 470 power ground (substrate) Fig.6 Stereo BTL test/application diagram. 10 Product specification TDA8563AQ V P 2200 100 diagnostic output 9 7 MGL074 ...
Page 11
... F The circuit in Fig.7 slowly ramps up the voltage at the mode select switch pin when switching on and results in fast muting when switching off. MGD959 Product specification TDA8563AQ (1) ( MLB667 ...
Page 12
... Fig.9 Output power as a function of supply voltage kHz handbook, full pagewidth Fig.10 Output power as a function of frequency; THD = 0.5%; V 2001 Feb 21 (1) (2) ( Product specification TDA8563AQ ( (Hz MGA905 18 MLB668 5 10 ...
Page 13
... On condition. (2) Mute condition. Fig.12 Ripple rejection as a function of frequency; V 2001 Feb 21 (1) (2) ( (1) ( Product specification TDA8563AQ (Hz (Hz (p-p ripple s MLB669 5 10 MLB670 5 10 ...
Page 14
... Fig.13 Channel separation as a function of frequency; V 150 handbook, full pagewidth I q (mA) 130 110 Fig.14 Quiescent current as a function of supply voltage; R 2001 Feb Product specification TDA8563AQ (Hz MLB671 MGA909 18 ...
Page 15
... 20.0 12.2 10 3.4 1.7 5.08 19.6 11.8 REFERENCES JEDEC EIAJ 15 non-concave view B: mounting base side 3.4 12.4 2.4 2.1 6 4.3 3.1 11.0 1.6 1.8 EUROPEAN PROJECTION Product specification TDA8563AQ SOT141 2.00 0.8 0.25 0.03 1.45 ISSUE DATE 97-12-16 99-12-17 ...
Page 16
... If the temperature of the soldering iron bit is less than 300 C it may remain in contact for seconds. If the bit temperature is between 300 and 400 C, contact may seconds. SOLDERING METHOD DIPPING suitable 16 Product specification TDA8563AQ ). If the stg(max) WAVE (1) suitable ...
Page 17
... Product specification TDA8563AQ (1) These products are not Philips Semiconductors ...
Page 18
... Philips Semiconductors 2 40 W/2 stereo BTL car radio power amplifier with diagnostic facility 2001 Feb 21 NOTES 18 Product specification TDA8563AQ ...
Page 19
... Philips Semiconductors 2 40 W/2 stereo BTL car radio power amplifier with diagnostic facility 2001 Feb 21 NOTES 19 Product specification TDA8563AQ ...
Page 20
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + 101 ...