tc58fvt160 TOSHIBA Semiconductor CORPORATION, tc58fvt160 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/6/670/toshiba_semiconductor_corporation_sml.jpg)
tc58fvt160
Manufacturer Part Number
tc58fvt160
Description
16-mbit 2m ? 8 Bits / 1m ? 16 Bits Cmos Flash Memory
Manufacturer
TOSHIBA Semiconductor CORPORATION
Datasheet
1.TC58FVT160.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
tc58fvt160AFT-70
Manufacturer:
TOSHIBA
Quantity:
1 400
Part Number:
tc58fvt160AFT70
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
Company:
Part Number:
tc58fvt160ATG-70
Manufacturer:
ROHM
Quantity:
3 000
Company:
Part Number:
tc58fvt160ATG70
Manufacturer:
TOSHIBA
Quantity:
396
Company:
Part Number:
tc58fvt160AXB-70
Manufacturer:
TOSHIBA
Quantity:
720
Part Number:
tc58fvt160AXB-70
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
Company:
Part Number:
tc58fvt160FT-10
Manufacturer:
TOSHIBA
Quantity:
1 400
Part Number:
tc58fvt160FT-85
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
HARDWARE SEQUENCE FLAGS
an auto mode operation. The output data is read out using the same timing as that used when CE = OE = V
Read Mode. The
Hardware Sequence flag is read to determine the device status and the result of the operation is verified by
comparing the read-out data with the original data.
The TC58FVT160A/B160A has a Hardware Sequence flag which allows the device status to be determined during
The device re-enters Read Mode automatically after an auto mode operation has been completed successfully. The
Notes: DQ outputs cell data and
DQ7 (
function. DATA polling begins on the rising edge of WE in the last bus cycle. In an Auto-Program operation,
DQ7 outputs inverted data during the programming operation and outputs actual data after programming has
finished. In an auto-erase operation, DQ7 outputs 0 during the Erase operation and outputs 1 when the Erase
operation has finished. If an Auto-Program or auto-erase operation fails, DQ7 simply outputs the data.
In Progress
Time Limit
Exceeded
During an Auto-Program or auto-erase operation, the device status can be determined using the data polling
When the operation has finished, the address latch is reset. Data polling is asynchronous with the OE signal.
DQ0 and DQ1 pins are reserved for future use.
0 is output on DQ0, DQ1 and DQ4.
(1) Data output from an address to which Write is being performed is undefined.
(2) Output when the block address selected for Auto Block Erase is specified and data is read from there.
(3) Output when a block address not selected for Auto Block Erase and data is read from there.
DATA
During Auto Chip Erase, all blocks are selected.
Auto Programming
Read in Program Suspend
Auto Programming
Auto Erase
Programming in Erase Suspend
Suspend
In Erase
In Auto
RY
Erase
polling)
/
BY
STATUS
Erase Hold Time
output can be either High or Low.
Programming
Auto Erase
Read
RY
/
BY
(1)
goes High-Impedence when the operation has been completed.
Not-selected
Not-selected
Not-selected
Not-selected
Selected
Selected
Selected
Selected
(2)
(3)
DQ
DQ
DQ
DQ
DQ
DQ7
Data
Data
0
0
0
0
1
0
7
7
7
7
7
TC58FVT160/B160AFT/AXB-70,-10
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
DQ6
Data
Data
1
Data
Data
DQ5
0
0
0
0
0
0
0
0
1
1
1
Data
Data
DQ3
0
0
0
1
1
0
0
0
0
1
0
2002-08-06 14/41
Toggle
Toggle
Toggle
Toggle
DQ2
Data
Data
NA
NA
1
1
1
1
1
RY
High-Z
High-Z
High-Z
0
0
0
0
0
0
0
0
0
0
/
BY
IL
in