tza3012ahw NXP Semiconductors, tza3012ahw Datasheet - Page 45

• Manufacturer Part Number: tza3012ahw
• Description: 30 Mbits/s Up To 3.2 Gbits/s A-ratetm Fibre Optic Receiver
• Manufacturer: NXP Semiconductors

Philips Semiconductors
Notes
1. Default settings: UI = LOW (pre-programmed mode; see Table 1); DR0 = LOW, DR1 = HIGH, DR2 = LOW
2. The total supply current and power dissipation is dependent on the IC setups such as swing and loop modes and
3. The output swing is adjustable in 16 steps controlled by bits RFS in I
4. The output swing is adjustable in 16 steps controlled by bits MFS in I
5. With 50% duty cycle.
6. The RF input is protected against a differential overvoltage; the maximum input current is 30 mA. It is assumed that
7. The slice level is adjustable in 256 steps controlled by I
8. The hysteresis is adjustable in 8 steps controlled by bits HYS1 and HYS2 in I
9. The J
10. The J
11. The J
2003 May 21
Jitter tolerance
J
SYMBOL
tol(p-p)
30 Mbits/s up to 3.2 Gbits/s
A-rate
(STM16/OC48); INSEL = HIGH (limiter 1 active); WINSIZE = HIGH (1000 ppm); ENBA = HIGH (automatic byte
alignment); ENLOUTQ = HIGH (DOUT, COUT disabled); ENLINQ = HIGH (DLOOP, CLOOP disabled);
DMXR0 = HIGH, DMXR1 = HIGH (DMX ratio 1:16); CREF and CREFQ = 19.44 MHz; LOSTH2 not connected
(LOS2 switched off); D00 to D15 and D00Q to D15Q, FP, FPQ, PARITY, PARITYQ, POCLK, POCLKQ, PRSCLO
and PRSCLOQ not connected.
termination conditions.
standard LVPECL mode only swing = 12 (default) should be used.
both inputs carry a complementary signal of the specified peak-to-peak value.
(address C1H).
(address BDH) and LIMLOS2CNF (address BFH).
tol(p-p)
tol(p-p)
tol(p-p)
jitter tolerance
(peak-to-peak value)
fibre optic receiver
min. value is 0.25UI for T
min. value is 0.25UI for T
min. value is 0.25UI for T
PARAMETER
amb
amb
amb
STM1/OC3 mode
(ITU-T G.958);
PRBS (2
STM4/OC12 mode
(ITU-T G.958);
PRBS (2
STM16/OC48 mode
(ITU-T G.958);
PRBS (2
= 40 C to 0 C at f = 65 kHz and 1 MHz.
= 40 C to 0 C at f = 250 kHz and 5 MHz.
= 40 C to 0 C at f = 1 MHz and 20 MHz.
f = 6.5 kHz
f = 65 kHz
f = 1 MHz
f = 25 kHz
f = 250 kHz
f = 5 MHz
f = 100 kHz
f = 1 MHz
f = 20 MHz
CONDITIONS
31
31
31
1); note 9
1); note 10
1); note 11
45
2
C-bus registers LIMSLICE1 (address C0H) and LIMSLICE2
2
2
C-bus register CBH.
C-bus register IOCNF3 (address C8H). In
3
0.3
0.3
3
0.3
0.3
3
0.3
0.3
MIN
2
C-bus registers LIMLOS1CNF
10
1
0.5
10
1
0.5
10
1
0.5
TYP
TZA3012AHW
Product specification
MAX
UI
UI
UI
UI
UI
UI
UI
UI
UI
UNIT