z8f0813 ZiLOG Semiconductor, z8f0813 Datasheet - Page 131
z8f0813
Manufacturer Part Number
z8f0813
Description
High-performance 8-bit Microcontrollers
Manufacturer
ZiLOG Semiconductor
Datasheet
1.Z8F0813.pdf
(247 pages)
- Current page: 131 of 247
- Download datasheet (4Mb)
PS024314-0308
Interrupts
Calibration and Compensation
4. When the first conversion in continuous operation is complete (after 5129 system
5. The ADC writes a new data result every 256 system clock cycles. For each completed
6. To disable continuous conversion, clear the CONT bit in the ADC Control register
The ADC is able to interrupt the CPU whenever a conversion has been completed and the
ADC is enabled.
When the ADC is disabled, an interrupt is not asserted; however, an interrupt pending
when the ADC is disabled is not cleared.
Z8 Encore! XP
error, with the compensation data stored in Flash memory. Alternatively, user code can
perform its own calibration, storing the values into Flash themselves.
Factory Calibration
Devices that have been factory calibrated contain nine bytes of calibration data in the
Flash option bit space. This data consists of three bytes for each reference type. For a list
of input modes for which calibration data exists, see
There is 1 byte for offset, 2 bytes for gain correction.
User Calibration
If you have precision references available, its own external calibration can be performed,
storing the values into Flash themselves.
clock cycles, plus the 40 cycles for power-up, if necessary), the ADC control logic
performs the following operations:
–
–
conversion, the ADC control logic performs the following operations:
–
–
to 0.
CEN resets to 0 to indicate the first conversion is complete. CEN remains 0 for all
subsequent conversions in continuous operation.
An interrupt request is sent to the Interrupt Controller to indicate the conversion is
complete.
Writes the 11-bit two’s complement result to {ADCD_H[7:0], ADCD_L[7:5]}.
An interrupt request to the Interrupt Controller denoting conversion complete.
®
F0823 Series ADC can be factory calibrated for offset error and gain
Zilog Calibration Data
Z8 Encore! XP
Product Specification
Analog-to-Digital Converter
®
F0823 Series
on page 147.
121
Related parts for z8f0813
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Z8 Encore!? Microcontroller With Flash Memory And 10-bit A/d Converter
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z8 Encore! Xp F64xx Series
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z8 Encore Motor Control Flash Mcus
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z8 Encore XP-R F08xA Series with eXtended Peripherals
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore Microcontrollers with Flash Memory and 10-Bit A/D Converter
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore-R Motor Control Flash MCUs
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore-R Motor Control Series
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 MCU MICROCONTROLLERS
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore / Microcontrollers with Flash Memory and 10 Bit A/D Converter
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
Z8 MCU MICROCONTROLLERS
Manufacturer:
Zilog.
Datasheet:
Part Number:
Description:
Ez80f91 Mini Enet Module
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z90233, Z90234, And Z90231 Ezvision 200 Television Controller
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Digital Television Controllers
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Television Controllers
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
40-pin Low-cost Digital Television Controller
Manufacturer:
ZiLOG Semiconductor
Datasheet: