z8f0813 ZiLOG Semiconductor, z8f0813 Datasheet - Page 86
z8f0813
Manufacturer Part Number
z8f0813
Description
High-performance 8-bit Microcontrollers
Manufacturer
ZiLOG Semiconductor
Datasheet
1.Z8F0813.pdf
(247 pages)
- Current page: 86 of 247
- Download datasheet (4Mb)
PS024314-0308
generated and the count value in the Timer High and Low Byte registers is reset to
and counting resumes. The
interrupt is because of an input capture event.
If no Capture event occurs, the timer counts up to the 16-bit Compare value stored in the
Timer Reload High and Low Byte registers. Upon reaching the Reload value, the timer
generates an interrupt, the count value in the Timer High and Low Byte registers is reset to
0001H
the timer interrupt is not caused by an input capture event.
Follow the steps below for configuring a timer for CAPTURE RESTART mode and initi-
ating the count:
1. Write to the Timer Control register to:
2. Write to the Timer High and Low Byte registers to set the starting count value
3. Write to the Timer Reload High and Low Byte registers to set the Reload value.
4. Clear the Timer PWM High and Low Byte registers to 0000H. This allows the
5. Enable the timer interrupt, if appropriate, and set the timer interrupt priority by writing
6. Configure the associated GPIO port pin for the Timer Input alternate function.
7. Write to the Timer Control register to enable the timer and initiate counting.
In CAPTURE mode, the elapsed time from timer start to Capture event can be calculated
using the following equation:
COMPARE Mode
In COMPARE mode, the timer counts up to the 16-bit maximum Compare value stored in
the Timer Reload High and Low Byte registers. The timer input is the system clock. Upon
reaching the Compare value, the timer generates an interrupt and counting continues (the
–
–
–
–
(typically
software to determine if interrupts were generated by either a Capture or a Reload
event. If the PWM High and Low Byte registers still contain
the interrupt was generated by a Reload.
to the relevant interrupt registers. By default, the timer interrupt is generated for both
input Capture and Reload events. If appropriate, configure the timer interrupt to be
generated only at the input Capture event or the Reload event by setting TICONFIG
field of the TxCTL1 register.
Capture Elapsed Time (s)
and counting resumes. The
Disable the timer.
Configure the timer for CAPTURE RESTART mode. Setting the mode also
involves writing to
Set the prescale value.
Set the Capture edge (rising or falling) for the Timer Input.
0001H
).
INPCAP
TMODEHI
=
INPCAP
(
------------------------------------------------------------------------------------------------- -
bit in TxCTL1 register is set to indicate the timer
Capture Value Start Value
bit in TxCTL1 register.
System Clock Frequency (Hz)
bit in TxCTL1 register is cleared to indicate
–
Z8 Encore! XP
0000H
Product Specification
) Prescale
×
after the interrupt,
®
F0823 Series
0001H
Timers
76
Related parts for z8f0813
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Z8 Encore!? Microcontroller With Flash Memory And 10-bit A/d Converter
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z8 Encore! Xp F64xx Series
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z8 Encore Motor Control Flash Mcus
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z8 Encore XP-R F08xA Series with eXtended Peripherals
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore Microcontrollers with Flash Memory and 10-Bit A/D Converter
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore-R Motor Control Flash MCUs
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore-R Motor Control Series
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 MCU MICROCONTROLLERS
Manufacturer:
ZILOG [Zilog, Inc.]
Datasheet:
Part Number:
Description:
Z8 Encore / Microcontrollers with Flash Memory and 10 Bit A/D Converter
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
Z8 MCU MICROCONTROLLERS
Manufacturer:
Zilog.
Datasheet:
Part Number:
Description:
Ez80f91 Mini Enet Module
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Z90233, Z90234, And Z90231 Ezvision 200 Television Controller
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Digital Television Controllers
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
Television Controllers
Manufacturer:
ZiLOG Semiconductor
Datasheet:
Part Number:
Description:
40-pin Low-cost Digital Television Controller
Manufacturer:
ZiLOG Semiconductor
Datasheet: