pcf50603 NXP Semiconductors, pcf50603 Datasheet
pcf50603
Available stocks
Related parts for pcf50603
pcf50603 Summary of contents
Page 1
... DATA SHEET PCF50603 Controller for power supply and battery management Preliminary specification INTEGRATED CIRCUITS 2003 Oct 31 ...
Page 2
... CHARACTERISTICS 11 APPLICATION INFORMATION 12 PACKAGE OUTLINE 13 SOLDERING 13.1 Introduction to soldering surface mount packages 13.2 Reflow soldering 13.3 Wave soldering 13.4 Manual soldering 13.5 Suitability of surface mount IC packages for wave and reflow soldering methods 14 DATA SHEET STATUS 15 DEFINITIONS 16 DISCLAIMERS 17 PURCHASE OF PHILIPS I 2 Preliminary specification PCF50603 2 C COMPONENTS ...
Page 3
... System control 2 Serial 400 kHz I C-bus interface to transfer the control data between the PCF50603 and the host controller On/Off Control (OOC) module to control the power ramp-up and ramp-down sequences for the handset. Furthermore it determines the supported system operating states: NOPOWER, SAVE, STANDBY and ACTIVE to realize minimum power consumption in all states ...
Page 4
... APPLICATIONS Mobile phones. 3 GENERAL DESCRIPTION The PCF50603 is a highly integrated solution for power supply generation, battery management including charging and a SIM card interface including supply generation. The device is controlled by a host controller via a 400 kHz +85 C; unless otherwise specified. ...
Page 5
... Philips Semiconductors Controller for power supply and battery management 5 ORDERING INFORMATION TYPE NUMBER NAME PCF50603HN HVQFN48 plastic thermal enhanced very thin quad flat package; no leads; 2003 Oct 31 PACKAGE DESCRIPTION 48 terminals; body Preliminary specification PCF50603 VERSION SOT778-1 ...
Page 6
... Acrobat reader. white to force landscape pages to be ... ONKEY_N RSTHC_N 27 11 PCF50603 TS temp_ok RTC AND ALARM 2 SCL 2 control data I C-BUS 3 INTERFACE SDA status data reference voltage 28 ON-CHIP REFC REFERENCE ...
Page 7
... RF2REG output voltage 32.768 kHz oscillator output 32.768 kHz oscillator input On-key (active LOW); input with internal pull-up resistor to VINT reference voltage bypass capacitor connection internal supply voltage output backup battery supply voltage main battery supply voltage charger voltage 7 Preliminary specification PCF50603 (1) ...
Page 8
... SIM clock output to the SIM card SIM reset output to the SIM card (active LOW) enable SIMI and SIMREG general purpose open-drain output 3 general purpose open-drain output 2 general purpose open-drain output 1 except pin V who has one clamp in series with a 500 SS CHG 8 Preliminary specification PCF50603 (1) resistor connected ...
Page 9
... All GND and V pads are connected to the ground plane. SS 2003 Oct PCF50603HN SDA 2 SCL 1 Fig.2 Pin configuration. 9 Preliminary specification PCF50603 25 OSCO 26 OSCI 27 ONKEY_N REFC 28 29 VINT 30 V SAVE 31 V BAT 32 V CHG 33 CHGDRV 34 CHGCUR/BATMAX 35 CPVDD ...
Page 10
... Philips Semiconductors Controller for power supply and battery management 8 FUNCTIONAL DESCRIPTION 8.1 On/off control 8.1.1 O PERATING STATES The PCF50603 has four operating states (see Fig.3): NOPOWER SAVE STANDBY ACTIVE. handbook, full pagewidth V SAVE > V VERY_LOW_BACK 8.1.2 R ESET GENERATION The OOC generates an internal and an external reset each time the system goes from STANDBY to ACTIVE state ...
Page 11
... Before the supplies are turned on, the internal 32 kHz clock is already stable. After power up of the IOVDD supply the external clock on pin CLK32K becomes available. Fig.5 Reset generation timing diagram (STANDBY - ACTIVE - STANDBY transition). 2003 Oct 31 ACTIVE t reset = 10 ms ACTIVE t reset = 10 ms SIM emergency deactivation 11 Preliminary specification PCF50603 STANDBY MDB682 STANDBY MDB683 ...
Page 12
... If the watchdog is not reset in time, the PCF50603 automatically goes to the STANDBY state when the watchdog timer expires. Status bit WDTEXP is set when the watchdog timer expires. After ...
Page 13
... There are no timing requirements for interrupt service response times. All events that require immediate actions are performed by the PCF50603 without any action by the system controller. The function of the interrupt module is to capture, mask and combine the interrupt signals from the modules that can generate an interrupt ...
Page 14
... IRQ_N becomes inactive high as soon as the read sequence of the last INTx register containing an active interrupt starts. Fig.9 Interrupt timing; interrupt captured during read sequence. 2003 Oct 31 (1) read request & read address INT1 (1) read request & read address INT1 14 Preliminary specification read read INT2 INT3 minimal 1 CLK32 read read INT2 INT3 PCF50603 MDB685 MDB686 ...
Page 15
... Power supply modules In total 11 power supply modules are available in the PCF50603; see Table 1: Three regulators for supplying the digital and analog circuitry (D1REG, D2REG and D3REG). These regulators support the ECO mode One regulator for high current supply (HCREG) ...
Page 16
... Only an external power PNP transistor is required to control the charge current. The CC and CCCV control circuitry is fully integrated in the PCF50603 charging module. In CCCV configuration the charging process for Li-ion/Li-pol batteries is performed under control of the host controller ...
Page 17
... ACTIVE state, the host controller should initiate a transition to STANDBY state. In case the host controller does not initiate a transition to the STANDBY state within eight seconds after the interrupt occurred, the OOC forces the PCF50603 to the STANDBY state in order to prevent a too deep discharge of the battery. 17 Preliminary specification ...
Page 18
... STANDBY state. In case the host controller does not initiate a transition to the STANDBY state within 1 second after the interrupt occurred, the OOC forces the PCF50603 to the STANDBY state in order to prevent damage to the circuit. The hysteresis and debounce time have been built in to prevent fast cycling of the HIGHTMP signal ...
Page 19
... LED modulator (LED1 and LED2) The PCF50603 contains two LED modulators (LED1 and LED2), which can be selected as input for any of the GPO outputs. The LED modulator of the PCF50603 is used for the control of the indicator LEDs. They offer the following features: The LED driver can select eight different repetition periods Capable of generating eight different blinking patterns ...
Page 20
... BAT SAVE REC1_N, SIMVCC, RF12VBAT, HCVBAT, REC2_N pin V CHG other pins MM; note +85 C; unless otherwise specified. CONDITIONS DC rectified sine wave; 100 Hz to 120 Hz; note 1 32 kHz clock available 20 Preliminary specification PCF50603 MIN. MAX. 0.5 +6.5 0.5 +6.5 0.5 +20 0.5 +6.5 10 +10 10 +10 2000 ...
Page 21
... Under specific conditions a nominal current of 300 mA can be delivered. 2. Maximum current depends on the selected output voltage. At 3.50 V, 4.00 V and 4.50 V the maximum output current is 75 mA. At 5.00 V output voltage the maximum output current is 50 mA. 2003 Oct 31 CONDITIONS note 1 note 2 21 Preliminary specification PCF50603 MIN. TYP. MAX. UNIT 1.20 3.20 V 100 mA 2 ...
Page 22
... LOWVOLT_N PWREN1 6 PWREN2 5 RSTHC_N 11 IRQ_N 10 CLK32K 4 SDA 3 SCL 2 SIMIOHC 9 SIMCKHC 8 SIMRSHC_N revmod 7 PCF50603 RAM 1.8 V FLASH 1.8 V AUXADCx MICP MICN VDDA VDDD PCF5213 VDDE3 VDDA VDDC VDDE1 VDDE2 ONKEY AUXON_N GPON0 RFSIGx RSTON SIMERRN CLK32I SDA SCL SIMIO SIMCLK GPOx ...
Page 23
... 2.5 scale (1) ( 4.25 6.1 4.25 0.4 4.4 4.4 3.95 5.9 3.95 REFERENCES JEDEC JEITA - - - - - - 23 Preliminary specification detail 0.5 0.1 0.05 0.05 0.1 0.3 EUROPEAN PROJECTION PCF50603 SOT778 ISSUE DATE 02-07-05 ...
Page 24
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 24 Preliminary specification PCF50603 ...
Page 25
... Hot bar or manual soldering is suitable for PMFP packages. 2003 Oct 31 (1) (3) , TFBGA, VFBGA not suitable not suitable suitable not recommended not recommended not suitable 25 Preliminary specification PCF50603 SOLDERING METHOD (2) WAVE REFLOW suitable (4) suitable suitable (5)(6) suitable (7) suitable not suitable ...
Page 26
... Preliminary specification PCF50603 DEFINITION These products are not Philips Semiconductors ...
Page 27
... Philips. This specification can be ordered using the code 9398 393 40011. 2003 Oct 31 C COMPONENTS 2 C components conveys a license under the Philips’ system provided the system conforms to the I 27 Preliminary specification PCF50603 2 C patent to use the 2 C specification defined by ...
Page 28
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2003 All rights are reserved. Reproduction in whole or in part is prohibited ...