sc16c652b NXP Semiconductors, sc16c652b Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
sc16c652b
Manufacturer Part Number
sc16c652b
Description
5v, 3.3 V And 2.5v Dual Uart, 5 Mbit/s Max. ,with 32-byte Fifos And Infrared Irda Encoder/decoder
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C652B.pdf
(43 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C652B
Manufacturer:
PHILIPS
Quantity:
42
Company:
Part Number:
sc16c652bIB48
Manufacturer:
AD
Quantity:
9 600
Part Number:
sc16c652bIB48
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
sc16c652bIB48,128
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c652bIB48,151
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c652bIB48,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
SC16C652B_4
Product data sheet
7.4 Interrupt Status Register (ISR)
The SC16C652B provides six levels of prioritized interrupts to minimize external software
interaction. The Interrupt Status Register (ISR) provides the user with six interrupt status
bits. Performing a read cycle on the ISR will provide the user with the highest pending
interrupt level to be serviced. No other interrupts are acknowledged until the pending
interrupt is serviced. A lower level interrupt may be seen after servicing the higher level
interrupt and re-reading the interrupt status bits.
data values (bits 5:0) for the six prioritized interrupt levels and the interrupt sources
associated with each of these interrupt levels.
Table 14:
Table 15:
Priority
level
1
2
2
3
4
5
6
Bit
7:6
5:4
3:1
0
Symbol
ISR[7:6]
ISR[5:4]
ISR[3:1]
ISR[0]
ISR[5]
0
0
0
0
0
0
1
Interrupt source
Interrupt Status Register bits description
ISR[4]
0
0
0
0
0
1
0
Description
FIFOs enabled. These bits are set to a logic 0 when the FIFOs are not being
used in the 16C450 mode. They are set to a logic 1 when the FIFOs are
enabled in the SC16C652B mode.
INT priority bits 4:3. These bits are enabled when EFR[4] is set to a logic 1.
ISR[4] indicates that matching Xoff character(s) have been detected. ISR[5]
indicates that CTS, RTS have been generated. Note that once set to a
logic 1, the ISR[4] bit will stay a logic 1 until Xon character(s) are received.
INT priority bits 2:0. These bits indicate the source for a pending interrupt at
interrupt priority levels 1, 2, and 3 (see
INT status.
Rev. 04 — 1 September 2005
logic 0 or cleared = default condition
logic 0 or cleared = default condition
logic 0 or cleared = default condition
logic 0 = an interrupt is pending and the ISR contents may be used as a
pointer to the appropriate interrupt service routine
logic 1 = no interrupt pending (normal default condition)
ISR[3]
0
0
1
0
0
0
0
Dual UART with 32-byte FIFOs and IrDA encoder/decoder
ISR[2]
1
1
1
0
0
0
0
ISR[1]
1
0
0
1
0
0
0
Table 14 “Interrupt source”
ISR[0]
0
0
0
0
0
0
0
Table
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Source of the interrupt
LSR (Receiver Line Status
Register)
RXRDY (Received Data Ready)
RXRDY (Receive Data time-out)
TXRDY (Transmitter Holding
Register Empty)
MSR (Modem Status Register)
RXRDY (Received Xoff signal)/
Special character
CTS, RTS change of state
14).
SC16C652B
shows the
20 of 43