ht82m9aae Holtek Semiconductor Inc., ht82m9aae Datasheet - Page 16

• Manufacturer Part Number: ht82m9aae
• Description: Usb Mouse Encoder 8-bit Mcu With Eeprom
• Manufacturer: Holtek Semiconductor Inc.

tomatically after the measurement cycle is completed.
But in the other two modes the TON can only be reset by
instructions. The overflow of the timer/event counter is
one of the wake-up sources. No matter what the opera-
tion mode is, writing a ²0² to ET can disable the corre-
sponding interrupt services.
In the case of timer/event counter OFF condition, writing
data to the timer/event counter preload register will also
reload that data to the timer/event counter. But if the
timer/event counter is turned on, data written to it will
only be kept in the timer/event counter preload register.
The timer/event counter will still operate until overflow
occurs (a timer/event counter reloading will occur at the
same time). When the timer/event counter (reading
TMR) is read, the clock will be blocked to avoid errors.
As clock blocking may result in a counting error, this
must be taken into consideration by the programmer.
Input/Output Ports
There are 16 bidirectional input/output lines in the
microcontroller, labeled from PA to PB, which are
mapped to the data memory of [12H] and [14H] respec-
tively. All of these I/O ports can be used for input and
output operations. For input operation, these ports are
non-latching, that is, the inputs must be ready at the T2
rising edge of instruction ²MOV A,[m]² (m=12H or 14H).
For output operation, all the data is latched and remains
unchanged until the output latch is rewritten.
Each I/O line has its own control register (PAC and PBC)
to control the input/output configuration. With this con-
trol register, CMOS/NMOS/PMOS output or Schmitt
trigger input with or without pull-high/low resistor struc-
tures can be reconfigured dynamically under software
control. To function as an input, the corresponding latch
Rev. 1.20
Input/Output Ports
16
of the control register must write a ²1². The input source
also depends on the control register. If the control regis-
ter bit is ²1², the input will read the pad state. If the con-
trol register bit is ²0², the contents of the latches will
move to the internal bus. The latter is possible in the
²read-modify-write² instruction. For output function,
CMOS/NMOS/PMOS configurations can be selected
(NMOS and PMOS are available for PA only). These
control registers are mapped to locations 13H and 15H.
After a chip reset, these input/output lines remain at high
levels or in a floating state (depending on the
pull-high/low options). Each bit of these input/output
latches can be set or cleared by ²SET [m].i² and ²CLR
[m].i² (m=12H or 14H) instructions.
Some instructions first input data and then follow the
output operations. For example, ²SET [m].i², ²CLR
[m].i², ²CPL [m]², ²CPLA [m]² read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Each line of PA0~PA7, PB4/SDA and PB7/SCL has the
capability of waking-up the device.
There are pull-high/low options available for I/O lines.
Once the pull-high/low option of an I/O line is selected,
the I/O line have pull-high/low resistor. Otherwise, the
pull-high/low resistor is absent. It should be noted that a
non-pull-high/low I/O line operating in input mode will
cause a floating state.
It is recommended that unused or not bonded out I/O
lines should be set as output pins by software instruction
to avoid consuming power under input floating state.
HT82M9AEE/HT82M9AAE
August 13, 2007