lb11690 Sanyo Semiconductor Corporation, lb11690 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/5/586/sanyo_semiconductor_corporation_sml.jpg)
lb11690
Manufacturer Part Number
lb11690
Description
Pre-driver Ic For Brushless Motor Drive In Electric Bicycles
Manufacturer
Sanyo Semiconductor Corporation
Datasheet
1.LB11690.pdf
(19 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LB11690
Manufacturer:
ROHM
Quantity:
15 000
3. PWM Oscillator Circuit
4. Control Methods
5. Charge Pump Circuit
The PWM frequency is determined by the capacitor C (rated in F) connected to the PWM pin.
When a 270 pF capacitor is used, the frequency will be about 39 kHz. If the PWM frequency is too low, the motor
will generate audible noise at the switching frequency, and if it is too high, the power loss will increase. A frequency
in the range 20 to 50 kHz is desirable. Connect the ground side of this capacitor to a point as close as possible to the
IC ground pin to minimize the influence of output noise.
The output duty is determined by comparing the PWM oscillator waveform to the TOC pin voltage. When the TOC
pin voltage is about 1.2 V or lower, the duty will be 0%, and when that voltage is 3.0 V or higher, the duty will be
100%.
Normally, the integrating amplifier is used as a full feedback amplifier (with
the EI
input to the EI
increases.) When the EI
the EI pin voltage is lowered to a level close to the ground level by an IC
internal transistor. (This is to discharge the capacitor.) Therefore, do not
connect a low-impedance power supply directly to this pin, but rather input
the voltage through a resistor. Also, a pull-down resistor must be inserted
between the EI
control voltage is in the open state. If there is noise on the control voltage or if
it is desirable to suppress rapid fluctuations in the control voltage, a noise
rejection capacitor must be inserted between the EI
operating voltage range can be expanded by inputting the control voltage to
the EI
A speed control circuit using the FV pin can be implemented as shown in the
figure to control the motor so that a constant speed is maintained to a certain
degree despite variations in the load. A resistor of 25 kΩ or larger must be
used between the FV and EI
that the TOC pin voltage is adequately stable at low speeds.
The charge pump steps up the supply voltage to generate the high side FET gate voltage. The capacitor CP connected
between the CP1 and CP2 pins is used for step up, and charge is stored on the capacitor CB connected between the
VB and V
The CP capacitor is charged and discharged based on the PWM frequency. While increasing the capacitance of the
capacitor C increases current capacity of the VB power supply, if the capacitance is too large, the charge and
discharge operation may be inadequate. Note that the larger the capacitance of the capacitor VB, the more stable the
VB voltage will be. However, if that capacitance is too large, the time before the VB voltage is generated when
power is first applied will increase. While testing and evaluation is required to set the values of the capacitors CP and
CB, use the following table as a reference for the initial values.
When the V
voltage to fall. Care is required in application design to assure that this does not become a problem.
V
CC
f
CB ≥ CP 4
PWM
–
+
CP
CB
voltage
pin and the TOC pin connected directly), and the control voltage is
pin through a resistor voltage divider as shown in the figure.
CC
CC
1/(93000 C)
pins. The capacitances of CP and CB must have the following relationship.
+
+
supply voltage is under 20 V, the VB power supply current capacity falls rapidly causing the VB
pin. (Here, the output duty increases as the EI
pin and ground so that the motor does not operate when the
0.1 µF
24 V
1 µF
+
pin is set to the reset operating state by the RES pin,
+
pin. The feedback capacitor must be selected so
6800 pF
0.47 µF
36 V
LB11690, 11690H
+
pin and ground. The
+
voltage
Control voltage
Control voltage
To the FV pin
TOC
TOC
EI+
EI–
EI–
EI+
No. 7543-13/19